Tissue culture studies of blood vessel grafts. I. The cultivation in vitro of fresh normal adult aorta (dog, cat, rabbit, goat, monkey, and human).

M. Parshley,R. Deterling,C. C. Coleman

DOI: https://doi.org/10.1002/AJA.1000930204

1953-09-01

American Journal of Anatomy

Abstract:

What problem does this paper attempt to address?

Multiresponse Optimization of Cutting Force and Cutting Power in Chopping Agricultural Residues Using Grey-Based Taguchi Method

Van-Dam Vu,Thanh-Toan Nguyen,Ngoc-Hung Chu,Quoc-Huy Ngo,Ky-Thanh Ho,Van-Du Nguyen

DOI: https://doi.org/10.3390/agriculture10030051

2020-02-25

Agriculture

Abstract:Agricultural residues are the most abundant biomass and forage resources. Chopping is a precondition for either use, and reducing the shearing force has been considered as one of the most effective way to save energy. A smaller force can also permit more compact mechanical parts of chopping devices. In several cases, power consumption may be large, even when the shearing force is small, if the corresponding cutting velocity is high. Consequently, it is important to minimize both cutting force and power consumption simultaneously. This paper presents a practical approach to solve the multi-objective optimization problem for chopping processes of corn stalks. Applying the Taguchi design of experiments, a plan of 27 chopping tests was conducted. Based on the grey relational grade analysis and analysis of variance technique, optimum levels as well as the percentage contribution of such parameters were identified. Experimental results showed that the multi-response optimization problem in chopping corn stalks can be effectively addressed through the combination of Taguchi design and grey relational analysis. The results can be expanded for practical applications in design and operation of chopping machines for agricultural residues.
Robust optimization of energy consumption during mechanical processing of wood

Diego Jean de Melo,Taiane Oliveira Guedes,José Reinaldo Moreira da Silva,Anderson Paulo de Paiva

DOI: https://doi.org/10.1007/s00107-019-01458-z

2019-11-01

European Journal of Wood and Wood Products

Abstract:Aiming for mechanical processing with efficiency and performance, robust optimization techniques are important tools. The wood processing encourages these studies, since wood has a heterogeneous behavior during cutting and reacts in a hardly predictable way to process variations. The objective of this work was to find the equilibrium point between the mean and the variance of the cutting energy consumption, thus indicating optimal processing parameters that do not underlie the influence of the moisture variable. For this, 30 boards of <em class="EmphasisTypeItalic">Pinus taeda</em> were processed in a planer with a frequency inverter, which allowed to capture the processing data. The control variables for this process were: cutting motor rotation, feed motor rotation and radial depth of cut. With the voltage and current data, the specific energy was calculated. The optimum point for lower power consumption was determined by the mean square error (MSE) where the cutting motor rotation, feed motor rotation and cutting depth values were 1831.38 rpm, 835.22 rpm and 1.16 mm, respectively. Thus, the effect of moisture was neutralized.

materials science, paper & wood,forestry
Optimisation and Finite Element Simulation of the Chopping Process for Chopper Sugarcane Harvesting

Luxin Xie,Jun Wang,Shaoming Cheng,Bosheng Zeng,Zizeng Yang

DOI: https://doi.org/10.1016/j.biosystemseng.2018.08.004

IF: 5.002

2018-01-01

Biosystems Engineering

Abstract:High levels of mechanical damage are a major obstacle for the mechanical harvesting of sugarcane. A chopping system for use in a sugarcane harvester was developed and tested. The three influencing factors studied were the rotational speed of chopping drums (RS), the overlapping length of upper and lower chopping blades (OL) and the bevel angle (BA). The quality of chopping included the percentage of undamaged billets (PUB) and the standard deviation of chopping length (SDCL), and together with the average maximum chopping power consumption (PC) these were regarded as outputs. A Box-Behnken design was employed to conduct the experiments and build regression models. The optimised results indicated that when RS increased from 200 to 250 rpm on the condition that OL and BA were set as 2 mm and 21.8 degrees, respectively, PUB decreased from 97.0% to 95.6%, with PC increasing from 515 to 625 W and SDCL increasing from 1.24 to 1.36 mm. Based on these optimised parameters, a finite element model was established to simulate the chopping process. The chopping resistance of blades, stress distribution of sugarcane and blades in the chopping process were then analysed. Results showed that the maximum Von Mises stress of sugarcane, upper and lower chopping blades in the chopping process were about 16.87, 106.08 and 115.72 MPa, respectively. (C) 2018 IAgrE. Published by Elsevier Ltd. All rights reserved.
Multi-objective Process Parameter Optimization for Energy Saving in Injection Molding Process

Ning-yun Lu,Gui-xia Gong,Yi Yang,Jian-hua Lu

DOI: https://doi.org/10.1631/jzus.a1100250

2012-01-01

Abstract:This paper deals with a multi-objective parameter optimization framework for energy saving in injection molding process. It combines an experimental design by Taguchi’s method, a process analysis by analysis of variance (ANOVA), a process modeling algorithm by artificial neural network (ANN), and a multi-objective parameter optimization algorithm by genetic algorithm (GA)-based lexicographic method. Local and global Pareto analyses show the trade-off between product quality and energy consumption. The implementation of the proposed framework can reduce the energy consumption significantly in laboratory scale tests, and at the same time, the product quality can meet the pre-determined requirements.
Pareto Fronts of Machining Parameters for Trade-off among Energy Consumption, Cutting Force and Processing Time

Keyan He,Renzhong Tang,Mingzhou Jin

DOI: https://doi.org/10.1016/j.ijpe.2016.12.012

IF: 11.251

2016-01-01

International Journal of Production Economics

Abstract:Cutting parameter optimization of machining processes is crucial for green manufacturing and needs to take energy consumption, cutting force and processing time into consideration. This paper presents a method to optimize machining parameters considering the trade-off between environmental concerns and economic objectives. The model for all three objectives of energy consumption, cutting force, processing time and their relationships with machining parameters is established based on theoretical analysis, experiment design, and statistical regression to obtain Pareto fronts. Various algorithms determining strategies, including sharing function approach, VEGA, NSGA-Ⅱ and MOEA/D, are used to study the Pareto front. Examples of a cylindrical turning and a face milling are used to conduct relative validation experiments to evaluate the proposed method and the computational performance of all algorithms. All of the experiments were conducted on a CK6153i lathe and an XHK-714F CNC machining center cutting C45E4 carbon steels. Results demonstrate that the proposed method is effective in finding trade-off among the three objectives and obtaining reasonable application ranges of machining parameters from Pareto fronts.
Performance Evaluation of a Chopper System for Sugarcane Harvester

Luxin Xie,Jun Wang,Shaoming Cheng,Bosheng Zeng,Zizeng Yang

DOI: https://doi.org/10.1007/s12355-019-00714-z

2019-01-01

Sugar Tech

Abstract:Improving sugarcane chopper harvesters in terms of chopping quality is essential to reduce harvesting loss and costs. In this study, a chopper system used in a sugarcane harvester was developed and utilized to evaluate the effect of rotational speed of chopping drums (X1), overlapping length of upper and lower chopping blades (X2) and bevel angle (X3) on chopping quality and power requirement. Box-Behnken design combining with response surface method was employed to obtain the optimal operating parameters. The significance of independent variables and their interactions were tested by analysis of variance with 95% confidence limit (α = 0.05). The optimal values of the selected variables were obtained by solving the regression models, as well as by analyzing the response surface contour plots. The optimal values of three test variables were computed as X2 of 2 mm and X3 of 21.8°. Based on these conditions, when X1 increased from 200 to 250 rpm, the percentage of undamaged billets decreased from 97.0 to 95.6%, the average maximum chopping power requirements increased from 515 to 625 W, and the standard deviation of chopping length increased from 1.24 to 1.36 mm. Verification experiments indicated that the observed values were in agreement with the predicted values. A high-speed camera system was then applied to capture the stalk trajectory during chopping process. Results suggested that maintaining a stable and low conveying speed of sugarcanes during mechanical harvesting could reduce stalk damage and juice loss, which contributed to high chopping quality.
Analysis of Multi-Objective Optimization of Machining Allowance Distribution and Parameters for Energy Saving Strategy

Keyan He,Huajie Hong,Renzhong Tang,Junyu Wei

DOI: https://doi.org/10.3390/su12020638

IF: 3.9

2020-01-01

Sustainability

Abstract:Machining allowance distribution and related parameter optimization of machining processes have been well-discussed. However, for energy saving purposes, the optimization priorities of different machining phases should be different. There are often significant incoherencies between the existing research and real applications. This paper presents an improved method to optimize machining allowance distribution and parameters comprehensively, considering energy-saving strategy and other multi-objectives of different phases. The empirical parametric models of different machining phases were established, with the allowance distribution problem properly addressed. Based on previous analysis work of algorithm performance, non-dominated sorting genetic algorithm II and multi-objective evolutionary algorithm based on decomposition were chosen to obtain Pareto solutions. Algorithm performances were compared based on the efficiency of finding the Pareto fronts. Two case studies of a cylindrical turning and a face milling were carried out. Results demonstrate that the proposed method is effective in trading-off and finding precise application scopes of machining allowances and parameters used in real production. Cutting tool life and surface roughness can be greatly improved for turning. Energy consumption of rough milling can be greatly reduced to around 20% of traditional methods. The optimum algorithm of each case is also recognized. The proposed method can be easily extended to other machining scenarios and can be used as guidance of process planning for meeting various engineering demands.
Optimization of cutting position and mode for cabbage harvesting

Du Dongdong,Wang Jun,Qiu Shanshan

DOI: https://doi.org/10.3969/j.issn.1002-6819.2014.12.004

2014-01-01

Abstract:Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.
Optimisation of Cutting Parameters for Improving Energy Efficiency in Machining Process

Hu Luoke,Tang Renzhong,Cai Wei,Feng Yixiong,Ma Xiang

DOI: https://doi.org/10.1016/j.rcim.2019.04.015

IF: 10.103

2019-01-01

Robotics and Computer-Integrated Manufacturing

Abstract:Reducing the machining energy consumption (MEC) of machine tools for turning operations is significant to promote sustainable manufacturing. It has been approved that selecting optimal cutting (turning) parameters is an effective approach to reduce the cutting energy consumption (CEC) within the MEC. However, the potentiality for this approach to reduce the non-cutting energy consumption (NCEC) has not received sufficient attentions. Especially, the energy consumed for spindle rotation change (SRCE) was neglected. Thus, this article aims at developing an integrated MEC model with NCEC and SRCE considered. Then, Simulated Annealing (SA) is employed to find the optimal spindle rotation speed (SRS) and feed rate which result in the minimum MEC. A case study is conducted, where five parts with different cutting lengths are processed on a lathe. The experiment results show that SA can obtain the global optimum in a short computation time when the step sizes for SRS and feed rate are 0.1 and 0.001, respectively. The optimal solution achieves a 19.28% MEC reduction. Finally, the relation between the part length and the optimal SRS is analysed, and the consequence of MEC minimisation on machining time is discussed.
Hybrid taguchi-grey relational analysis approach for optimizing cutter operational parameters in selective cauliflower harvesting

Ajay Kushwah,P. K. Sharma,H. L. Kushwaha,Brij Bihari Sharma,A. K. Shrivastava,Ramineni Harsha Nag,Manojit Chowdhury,Gopal Carpenter,Rashmi Yadav

DOI: https://doi.org/10.1038/s41598-024-81323-z

IF: 4.6

2024-12-01

Scientific Reports

Abstract:Cauliflower is an important winter crop grown in India, its curds are rich in nutritional profile, containing valuable minerals and vitamins. However, cauliflower harvesting is mainly accomplished by hands, which is time-consuming and requires a high labour force. On the other hand, most developed cauliflower harvesters are once over or single pass type, which harvests all plants irrespective of their maturity. So, the selective harvester could improve the cauliflower curds yield, and then decrease the labour requirement. To improve the cutting performance of the selective cauliflower harvester, the working parameters of the chainsaw cutting mechanism need to be considered and optimized. This research investigates the impact of cutting height, feed (push) force, and cutting speed on the efficiency of the cutter during harvest. The Taguchi approach, together with grey relational analysis (GRA), was employed to identify the most favorable combination of operational parameters. In addition, the variance analysis was conducted to statistically examine the impact of multiple parameters. The findings indicated that the feed force was the major parameter that influenced the cutting force, splitting failure levels, and cutting time. The most effective parameter combination consisted of a cutting height of 15 mm, a feed force of 10 N, and a cutting speed of 5 m/s. The grey relational grade of the ideal parameter combination has shown a 0.322 increase in comparison to the grade achieved with the initially selected parameter combination. This setting was further incorporated in the developed selective cauliflower harvester to improve the performance of its cutting mechanism.

multidisciplinary sciences
Data-Driven Cutting Parameters Optimization Method in Multiple Configurations Machining Process for Energy Consumption and Production Time Saving

Xikun Zhao,Congbo Li,Xingzheng Chen,Jiabin Cui,Bao Cao

DOI: https://doi.org/10.1007/s40684-021-00373-0

2021-07-16

Abstract:Cutting parameters and machining configurations affect the energy consumption and production time in the machining process significantly. Previous cutting parameters optimization methods are proposed for a specific machining configuration that limits its generalization ability. However, the machining configuration varies constantly with actual machining tasks, which results in the predetermined optimization method is impractical. We propose a data-driven optimization method for the multiple machining configurations, aimed at reducing energy consumption and production time. Firstly, the analysis of the relationship between energy consumption and meta-actions under different machining states is carried out, and the Gaussian process regression (GPR)-based energy consumption model is proposed. Then, a multi-objective optimization model is proposed for energy consumption and production time reduction, which is solved via a multi-objective grey wolf optimization. Finally, the experiments are conducted to verify the validity of the proposed method and the influence of meta-actions on energy consumption and production time are explicitly analyzed. The case study indicates the proposed energy consumption model has better prediction accuracy for multiple machining configurations. Optimizing cutting parameters achieves a trade-off between energy consumption and production time. Moreover, the parametric influence indicates cutting speed is the most influential cutting parameter for energy consumption and production time.

engineering, mechanical, manufacturing,green & sustainable science & technology
Energy modeling and a method for reducing energy loss due to cutting load during machining operations

Jingxiang Lv,Tao Peng,Renzhong Tang

DOI: https://doi.org/10.1177/0954405418769922

2019-01-01

Abstract:In a typical part manufacturing system, machining operations represent a major proportion of the total energy consumption. The energy consumption (in the form of electricity power) of a machining operation can be divided into four types, that is, standby power, operational power, cutting power and power loss due to cutting load. Power loss due to cutting load includes the power loss caused by the friction of mechanical transmission and the power lost in the motor when the cutting load is applied to the spindle system. While the first three types of power consumption have been studied intensively by previous researchers, the power loss due to cutting load, which accounts for up to 20% of the cutting power consumption during machining operations, has received relatively less attention. This article proposes a novel model to characterize power loss due to cutting load, in which the power lost in the mechanical transmission and in the spindle motor are analyzed and modeled separately. Cutting tests have been carried out to validate the proposed model using two numerical control lathe machines. And a method has been developed for reducing energy loss caused by cutting load, which includes cutting force prediction, power loss due to cutting load prediction and decision making. The method was evaluated through its application in the process design for a shaft part, and the results show a significant saving of up to 70.8% of energy loss caused by cutting load.
Force and power requirement for development of cumin harvester: a dynamic approach

Mohit Kumar,Pramod Kumar Sahoo,Dilip Kumar Kushwaha,Indra Mani,Nrusingh Charan Pradhan,Abhishek Patel,Aqil Tariq,Sajid Ullah,Walid Soufan

DOI: https://doi.org/10.1038/s41598-024-64473-y

IF: 4.6

2024-06-14

Scientific Reports

Abstract:An experimental setup was developed for simulating the field conditions to determine the force and power required for cutting cumin crops in dynamic conditions. The effect of cutter bar speeds, forward speeds, and blade type on cutting force and power requirement for cutting cumin were also studied. Experiments were carried out at three levels: cutter bar speeds, forward speeds, and blade type. The results showed that all the factors significantly affected cutting force. The cutting force followed a decreasing trend with the increase in cutter bar speed. Whereas it followed an increasing trend with the increase in forward speed. The maximum cutting force for all three blades was observed at a cutter bar speed of 2.00 strokes.s -1 and forward speed of 0.46 m.s −1 . The idle power and actual power required for cutting the cumin crop were also determined based on the cutting force. The results obtained were validated by the power drawn from the power source while operating the cutter bar blades. The R 2 values for Blade-B1, Blade-B2, and Blade-B3 were 0.90, 0.82, and 0.88, respectively. The cutting force was primarily affected by the cutter bar speed, resulting in PCR values of 74.20%, 82.32%, and 81.75% for Blade-B1, Blade-B2, and Blade-B3, respectively, followed by the forward speed, which also had an impact on PCR values of 16.60%, 15.27%, and 18.25% for Blade-B1, Blade-B2, and Blade-B3, respectively. The cutting force for Blade-B1, Blade-B2, and Blade-B3 varied from 15.96 to 58.97 N, 21.08 to 76.64 N, and 30.22 to 85.31, respectively, for the selected range of cutter bar speed and forward speed. Blade-B1 had 18 and 30% less power consumption than Blade-B2 and Blade-B3, respectively.

multidisciplinary sciences
Spatial optimization of cropping pattern for sustainable food and biofuel production with minimal downstream pollution

P V Femeena,K P Sudheer,R Cibin,I Chaubey

DOI: https://doi.org/10.1016/j.jenvman.2018.01.060

2018-04-15

Abstract:Biofuel has emerged as a substantial source of energy in many countries. In order to avoid the 'food versus fuel competition', arising from grain-based ethanol production, the United States has passed regulations that require second generation or cellulosic biofeedstocks to be used for majority of the biofuel production by 2022. Agricultural residue, such as corn stover, is currently the largest source of cellulosic feedstock. However, increased harvesting of crops residue may lead to increased application of fertilizers in order to recover the soil nutrients lost from the residue removal. Alternatively, introduction of less-fertilizer intensive perennial grasses such as switchgrass (Panicum virgatum L.) and Miscanthus (Miscanthus x giganteus Greef et Deu.) can be a viable source for biofuel production. Even though these grasses are shown to reduce nutrient loads to a great extent, high production cost have constrained their wide adoptability to be used as a viable feedstock. Nonetheless, there is an opportunity to optimize feedstock production to meet bioenergy demand while improving water quality. This study presents a multi-objective simulation optimization framework using Soil and Water Assessment Tool (SWAT) and Multi Algorithm Genetically Adaptive Method (AMALGAM) to develop optimal cropping pattern with minimum nutrient delivery and minimum biomass production cost. Computational time required for optimization was significantly reduced by loose coupling SWAT with an external in-stream solute transport model. Optimization was constrained by food security and biofuel production targets that ensured not more than 10% reduction in grain yield and at least 100 million gallons of ethanol production. A case study was carried out in St. Joseph River Watershed that covers 280,000 ha area in the Midwest U.S. Results of the study indicated that introduction of corn stover removal and perennial grass production reduce nitrate and total phosphorus loads without compromising on food and biofuel production. Optimization runs yielded an optimal cropping pattern with 32% of watershed area in stover removal, 15% in switchgrass and 2% in Miscanthus. The optimal scenario resulted in 14% reduction in nitrate and 22% reduction in total phosphorus from the baseline. This framework can be used as an effective tool to take decisions regarding environmentally and economically sustainable strategies to minimize the nutrient delivery at minimal biomass production cost, while simultaneously meeting food and biofuel production targets.
Selection of a Cutting Mechanism and Optimization of Parameters for Coconut Harvesting Drone

B. Kailashkumar,S.S. Sivakumar,J. John Gunasekar,P.K. Padmanathan,V. Alex Albert,R. Ravikumar

DOI: https://doi.org/10.18805/ag.d-5610

2022-08-04

Agricultural Science Digest - A Research Journal

Abstract:Background: Coconut (Cocos nucifera L.) palm is an important cash crop in India and third-largest producer of coconut in the world. In general, the skilled workers climb to harvest the coconuts from the tree without any safety device. The coconut trees are very tall and injuries associated with coconut tree climbing, particularly falling from coconut trees is common in coconut plantations. In order to rectify the problem, an appropriate cutting system needs to be developed. Hence the characterizing physical and mechanical properties viz., peduncle thickness, width, shape, size, moisture content, density and also the cutting blade characteristics, were studied. Methods: The observed characteristics were used for the effective design of the cutting module. The cutting blades were selected for the investigation viz, circular saw blade and saw tooth blade. The parameters selected for the investigation are cutting speed (S) at three levels (15.70, 20.94 and 26.17 ms-1), the inclination angle of the blade (q) five levels (30, 45, 60, 75 and 90°), type of the blades (B) (regular tooth and ripped tooth pitch) and thickness of peduncle (T) three levels (30, 40 and 50 mm). Similarly for chain saw, the velocity of cutting speed (S) at three levels (500, 700 and 900 rpm), the inclination angle of blade (q) at three levels (45, 60 and 90°) and thickness of peduncle (T) three levels (30, 40 and 50 mm) were selected for the experiments. Result: The optimization of the selected levels of variables was done to achieve best performance to select the cutting speed, cutting angle and type of blade. The results showed that circular saw blades with irregular tooth pitch have higher cutting efficiency than circular saw blades with regular tooth pitch. It was found that cutting time increases linearly with decreasing cutting speed. It was observed that chainsaw gives better cut quality with minimum cutting time than saw blades.
Cutting Energy Consumption Modeling by Considering Tool Wear and Workpiece Material Properties for Multi-Objective Optimization of Machine Tools

Yue Meng,Shengming Dong,Xinsheng Sun,Shiliang Wei,Xianli Liu

DOI: https://doi.org/10.3390/coatings14060691

IF: 3.236

2024-06-02

Coatings

Abstract:The increasing demand for energy is leading to global depletion of fossil fuels and growing environmental pressures, which are issues that need to be addressed. Machine tools are basic energy-consuming equipment in manufacturing systems. However, existing theoretical models ignore tool wear as well as workpiece material properties. This makes it difficult to further improve the accuracy of the model. Therefore, this study begins with the point of view of energy dissipation in the metal material removal process. A milling power model for computer numerical control (CNC) machines, considering tool wear and workpiece material properties during machining, is established. At the same time, milling is taken as the research object. A multi-objective cutting parameter optimization model is established to ensure the surface quality of the workpiece. In addition, the cutting energy consumption is taken into account in the developed models. Based on the multi-objective manta ray foraging optimization algorithm (MOMRFO), the Pareto-optimal solution set under multiple cutting conditions is solved. Finally, the experimental results of optimized parameters are compared with empirical parameters. The average prediction accuracy of the proposed energy consumption prediction model is above 91%. The experiments show that machining quality improves by optimizing the cutting parameters, with SEC, MRR, and Ra increasing by more than 44%, 53%, and 38%, respectively. The goals of reducing energy consumption and increasing productivity are achieved.

materials science, multidisciplinary,physics, applied, coatings & films
Single and Multi-response Optimization of Scroll Machining Parameters by the Taguchi Method

Xu Dang,Maged Al-Rahawi,Tao Liu,Salah Taresh Abdo Mohammed

DOI: https://doi.org/10.1007/s12541-024-01026-3

IF: 2.0411

2024-05-08

International Journal of Precision Engineering and Manufacturing

Abstract:The precision of scroll machining plays a crucial role in scroll compressor efficiency. However, the improvement in scroll surface quality usually comes at the cost of an increase in energy consumption, so a trade-off between surface quality and energy consumption is required. Here in, we concentrate on optimizing several scroll end milling parameters including depth of cut, feed rate, cutting speed, and radial depth of cut to enhance the efficiency of scroll compressors, which greatly influence manufacturing responses like cutting force, surface roughness, and machining time. First, a set of scroll milling experiments are conducted and analyzed by the Taguchi L25 orthogonal array. Then, a single response optimization is done by the Taguchi method to show the impact of the milling parameters on each single response. Furthermore, the Taguchi method associated with the desirability function is applied to optimize the multi-response outputs. According to the analysis of variance (ANOVA) for the single-response, feed rate is found the most significant factor, while the results of the multi-response analysis prove that depth of cut with 37.53% is the most significant factor for the entire system. Finally, a quadratic regression analysis is performed to verify the validation of optimized results. The results revealed a 44.04% improvement in machining time, accompanied by a 2.46% enhancement in composite desirability. This demonstrated a perfect fit between the measured and expected values, achieving a balance between surface quality and energy consumption. The optimization results provide a guidance for the high-surface quality machining of scrolls and could be directly applied in the manufacturing processes of scroll compressors.

engineering, mechanical, manufacturing
Sequencing the features to minimise the non-cutting energy consumption in machining considering the change of spindle rotation speed

Luoke Hu,Ying Liu,Niels Lohse,Renzhong Tang,Jingxiang Lv,Chen Peng,Steve Evans

DOI: https://doi.org/10.1016/j.energy.2017.08.032

IF: 9

2017-01-01

Energy

Abstract:A considerable amount of energy consumed by machine tools is attributable to non-cutting operations, including tool path, tool change, and change of spindle rotation speed. The non-cutting energy consumption of the machine tool (NCE) is affected by the processing sequence of the features of a specific part (PFS) because the plans of non-cutting operations will vary based on the different PFS. This article aims to understand the NCE between processing a specific feature and its pre- or post-feature, especially the energy consumed during the speed change of the spindle rotation. Based on the developed model, a single objective optimisation problem is introduced that minimises the NCE. Then, Ant Colony Optimisation (ACO) is employed to search for the optimal PFS. A case study is developed to validate the effectiveness of the proposed approach. Two parts with 12 and 15 features are processed on a machining centre. The simulation experiment results show that the optimal or near-optimal PFS can be found. Consequently, 8.70% and 30.42% reductions in NCE are achieved for part A and part B, respectively. Further, the performance of ACO for our specific optimisation problem is discussed and validated based on comparisons with other algorithms.
A cutting parameter energy-saving optimization method considering tool wear for multi-feature parts batch processing

Congbo Li,Shaoqing Wu,Qian Yi,Xikun Zhao,Longguo Cui

DOI: https://doi.org/10.1007/s00170-022-09557-7

IF: 3.563

2022-07-13

The International Journal of Advanced Manufacturing Technology

Abstract:Cutting parameters and tool wear both have significant influence on energy consumption in the processing. In a multi-feature parts batch processing, tool wear values are continuously increasing with the proceeding of processing, leading to a higher energy consumption. To reduce the wear speed, cutting parameters should be continuously adjusted according to different states of tool wear during batch processing. However, current cutting parameter optimization studies only focus on one specific workpiece and the tool wear is seldom considered in the batch processing. To fill this research gap, a cutting parameter energy-saving optimization method considering tool wear for multi-feature parts batch processing was proposed in this paper. First, the synergistic effect mechanism of cutting parameters and tool wear on energy consumption in the batch processing was analyzed. On this basis, a multi-objective cutting parameter optimization model for multi-feature parts batch processing was established. Then, the multi-objective cuckoo search (MOCS) algorithm was used to solve the optimization model. Finally, an experimental case was carried out to verify the effectiveness and practicability of the proposed method. Results show that energy consumption and machining time can be, respectively, decreased by 22.9% and 4.1%. Meanwhile, a conflict relationship exists between the energy consumption and machining time in the processing and the trade-off of them is analyzed in this paper.

engineering, manufacturing,automation & control systems
A systematic method of optimization of machining parameters considering energy consumption, machining time, and surface roughness with experimental analysis

Chunhua Feng,Haohao Guo,Jingyang Zhang,Yugui Huang,Shi Huang

DOI: https://doi.org/10.1007/s00170-022-08772-6

IF: 3.563

2022-01-25

The International Journal of Advanced Manufacturing Technology

Abstract:For improving energy efficiency of machining process, extensive studies focused on how to establish energy consumption model and optimize cutting parameters. However, the existing methods lack a systematic method to promote the widespread use of energy efficiency methods in industry. This paper proposes a systematic method integrating energy model, experiment design, and multi-objective optimization model. Firstly, the energy model is established considering cutting energy and non-cutting energy. Then, the orthogonal experiment is designed with the three levels of four factors of spindle speed, feed speed, cutting depth, and cutting width in the X and Y cutting directions. The data of energy consumption, surface quality, and machining time are obtained to study the effects of different cutting elements and cutting directions. Meanwhile, the standby, spindle idling, feed, SEC (specific energy consumption), material cutting, and idling feed models of the CNC machine tools are established based on the experimental data. Additionally, five sets of experimental data are tested for verifying the accuracy of the established energy consumption model, which can reach 99.4%. Finally, a multi-objective optimization model for high efficiency and energy saving of processing process is established to optimize the cutting parameters considering energy consumption, processing time, and surface quality simultaneously. Combining the case of milling with constraints including machine tool performance, tool life, processing procedures, and processing requirements, the Pareto solution set is used to solve the Pareto of the target model. Through drawing a three-dimensional needle graph and two-dimensional histogram, the optimal cutting parameter combination for rough machining and semi-finish machining is provided assisting in promoting the application of the sustainable techniques in the industry.

Tissue culture studies of blood vessel grafts. I. The cultivation in vitro of fresh normal adult aorta (dog, cat, rabbit, goat, monkey, and human).

Multiresponse Optimization of Cutting Force and Cutting Power in Chopping Agricultural Residues Using Grey-Based Taguchi Method

Robust optimization of energy consumption during mechanical processing of wood

Optimisation and Finite Element Simulation of the Chopping Process for Chopper Sugarcane Harvesting

Multi-objective Process Parameter Optimization for Energy Saving in Injection Molding Process

Pareto Fronts of Machining Parameters for Trade-off among Energy Consumption, Cutting Force and Processing Time

Performance Evaluation of a Chopper System for Sugarcane Harvester

Analysis of Multi-Objective Optimization of Machining Allowance Distribution and Parameters for Energy Saving Strategy

Optimization of cutting position and mode for cabbage harvesting

Optimisation of Cutting Parameters for Improving Energy Efficiency in Machining Process

Hybrid taguchi-grey relational analysis approach for optimizing cutter operational parameters in selective cauliflower harvesting

Data-Driven Cutting Parameters Optimization Method in Multiple Configurations Machining Process for Energy Consumption and Production Time Saving

Energy modeling and a method for reducing energy loss due to cutting load during machining operations

Force and power requirement for development of cumin harvester: a dynamic approach

Spatial optimization of cropping pattern for sustainable food and biofuel production with minimal downstream pollution

​​Selection of a Cutting Mechanism and Optimization of Parameters for Coconut Harvesting Drone

Cutting Energy Consumption Modeling by Considering Tool Wear and Workpiece Material Properties for Multi-Objective Optimization of Machine Tools

Single and Multi-response Optimization of Scroll Machining Parameters by the Taguchi Method

Sequencing the features to minimise the non-cutting energy consumption in machining considering the change of spindle rotation speed

A cutting parameter energy-saving optimization method considering tool wear for multi-feature parts batch processing

A systematic method of optimization of machining parameters considering energy consumption, machining time, and surface roughness with experimental analysis

Selection of a Cutting Mechanism and Optimization of Parameters for Coconut Harvesting Drone