Abstract:Ammonia is a promising zero-carbon fuel, offering new possibilities for sustainable energy system development. In this study, ignition delay times (IDTs) of NH3/C2H4 mixtures with C2H4 contents of 0 %, 5 %, 10 %, and 25 % were measured using a shock tube at temperatures ranging from 1176 to 1904 K, pressures of 1.0-8.5 atm, and equivalence ratios of 0.5, 1.0 and 2.0. A laser absorption diagnostic system was developed to track the temporal evolution of NH3 concentration during the oxidation process behind the reflected shock waves. The experimental results indicate that the IDTs of the mixtures exhibit non-linear decrease with the addition of ethylene. Specifically, compared to pure ammonia, the addition of 5 %, 10 % and 25 % ethylene significantly increases the reactivity of the mixture, leading to a 36.7 %, 75.9 % and 90.2 % reduction in IDT at a temperature of 1563 K and a pressure of 1.0 atm, respectively. Moreover, the mixture exhibits similar reactivity under fuel-lean and stoichiometric conditions, which remains higher than the reactivity observed under fuel-rich conditions. Overall, the IDTs and the time required for complete consumption of the mixture decreases as temperature, pressure, and ethylene blending ratio increase. In order to simulate and analyze the reaction process of NH3/C2H4 mixtures, a detailed kinetic model was constructed based on previous studies by updating the interaction reaction between C2H4 and NH2 radical and validated against the current experimental results. Rate of production (ROP) and sensitivity analysis were performed to identify the primary consumption pathways of NH3/C2H4 and the significant impact of C2H4 on the reactivity. Additionally, due to the addition of C2H4, a substantial amount of NH2 radical participates in the H-abstraction reaction (C2H4 + NH2<=>C2H3 + NH3). This results in a reduced involvement of NH2 in the DeNO(x) process and, consequently, the NH3/C2H4 mixture exhibits a higher tendency to produce NOx compared to pure ammonia. Novelty and significance statement: Ammonia offers new possibilities for sustainable energy systems but faces challenges like low combustion rate and mixing with reactive fuels can effectively enhance the ignition characteristics of NH3. The ignition delay times and speciation NH3/C2H4 mixtures are systemically measured by using shock tube and laser absorption spectroscopy. A newly detailed kinetic NH3-C2H4 model is also developed based on previous studies by updating the interaction reaction between C2H4 and NH2 radical and validated against the current experimental results. The rate of production and sensitivity analysis reveal that the interaction reaction (C2H4 + NH2<=>C2H3 + NH3) have a significant impact on the ignition performance of the binary mixtures. Additionally, the DeNO(x) process of binary mixtures is suppressed due to the addition of C2H4, resulting a higher tendency to produce NOx. To our best knowledge, this is the first experimental study to systematically measure the ignition delay times and speciation data of NH3/C2H4 mixtures.

An Experimental and Detailed Kinetic Modeling Study of the Auto-Ignition of NH3/diesel Mixtures: Part 1- NH3 Substitution Ratio from 20% to 90%

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Stage-wise Kinetic Analysis of Ammonia Addition Effects on Two-Stage Ignition in Dimethyl Ether

Investigation of the Effect of Ammonia Addition on the Two-Stage Ignition Process of Dimethyl Ether Based on Chemical Kinetic Analysis

Revealing the High-Pressure Autoignition of Ammonia/1-Methylnaphthalene: RCM Measurements and Kinetic Modeling

An Experimental and Detailed Kinetic Modeling Study of the Auto-Ignition of NH3/diesel Mixtures: Part 2- Wide Pressures Up to 120Bar

Low-temperature auto-ignition characteristics of NH3/diesel binary fuel: Ignition delay time measurement and kinetic analysis

Investigating Autoignition Characteristics of Ammonia/Heptamethylnonane Mixtures over Wide Pressure Ranges: Rapid Compression Machine Measurements and Kinetic Modeling Study

Ignition Delay Time Measurements and Kinetic Modeling of Methane/diesel Mixtures at Elevated Pressures

Experimental and kinetic modeling study on auto-ignition of ammonia/n-heptane mixtures at intermediate temperatures

Experimental and modeling study on the ignition delay times of ammonia/methane mixtures at high dilution and high temperatures

Exploring the Interaction Chemistry of Ammonia with N-Hexadecane over Wide Pressure Ranges: an Experimental and Kinetic Modeling Study

Experimental and Modeling Study of the Oxidation of NH3/C2H4 Mixtures in a Shock Tube

Shock Tube and Modeling Study on the Ignition Delay Times of Ammonia/ethylene Mixtures at High Temperatures

An Experimental and Modeling Study on Auto-Ignition of Ammonia in an RCM with N2O and H2 Addition

Autoignition Behavior of Methanol/diesel Mixtures: Experiments and Kinetic Modeling

Kinetic study of ignition process of ammonia/n‐heptane fuel blends under engine conditions

An experimental and kinetic modeling study on the ignition characteristics of ammonia/ethanol at high temperatures

Investigating Auto-Ignition Characteristics and Kinetic Modeling of NH3/CH4 Mixtures Using an RCM

The effect of ammonia addition on the low-temperature autoignition of n-heptane: An experimental and modeling study

Experimental and Modeling Study of the Autoignition Characteristics of Commercial Diesel under Engine-Relevant Conditions