Abstract:Ammonia is a promising zero-carbon fuel, offering new possibilities for sustainable energy system development. In this study, ignition delay times (IDTs) of NH3/C2H4 mixtures with C2H4 contents of 0 %, 5 %, 10 %, and 25 % were measured using a shock tube at temperatures ranging from 1176 to 1904 K, pressures of 1.0-8.5 atm, and equivalence ratios of 0.5, 1.0 and 2.0. A laser absorption diagnostic system was developed to track the temporal evolution of NH3 concentration during the oxidation process behind the reflected shock waves. The experimental results indicate that the IDTs of the mixtures exhibit non-linear decrease with the addition of ethylene. Specifically, compared to pure ammonia, the addition of 5 %, 10 % and 25 % ethylene significantly increases the reactivity of the mixture, leading to a 36.7 %, 75.9 % and 90.2 % reduction in IDT at a temperature of 1563 K and a pressure of 1.0 atm, respectively. Moreover, the mixture exhibits similar reactivity under fuel-lean and stoichiometric conditions, which remains higher than the reactivity observed under fuel-rich conditions. Overall, the IDTs and the time required for complete consumption of the mixture decreases as temperature, pressure, and ethylene blending ratio increase. In order to simulate and analyze the reaction process of NH3/C2H4 mixtures, a detailed kinetic model was constructed based on previous studies by updating the interaction reaction between C2H4 and NH2 radical and validated against the current experimental results. Rate of production (ROP) and sensitivity analysis were performed to identify the primary consumption pathways of NH3/C2H4 and the significant impact of C2H4 on the reactivity. Additionally, due to the addition of C2H4, a substantial amount of NH2 radical participates in the H-abstraction reaction (C2H4 + NH2<=>C2H3 + NH3). This results in a reduced involvement of NH2 in the DeNO(x) process and, consequently, the NH3/C2H4 mixture exhibits a higher tendency to produce NOx compared to pure ammonia. Novelty and significance statement: Ammonia offers new possibilities for sustainable energy systems but faces challenges like low combustion rate and mixing with reactive fuels can effectively enhance the ignition characteristics of NH3. The ignition delay times and speciation NH3/C2H4 mixtures are systemically measured by using shock tube and laser absorption spectroscopy. A newly detailed kinetic NH3-C2H4 model is also developed based on previous studies by updating the interaction reaction between C2H4 and NH2 radical and validated against the current experimental results. The rate of production and sensitivity analysis reveal that the interaction reaction (C2H4 + NH2<=>C2H3 + NH3) have a significant impact on the ignition performance of the binary mixtures. Additionally, the DeNO(x) process of binary mixtures is suppressed due to the addition of C2H4, resulting a higher tendency to produce NOx. To our best knowledge, this is the first experimental study to systematically measure the ignition delay times and speciation data of NH3/C2H4 mixtures.

Experimental and Modeling Study of the Oxidation of NH3/C2H4 Mixtures in a Shock Tube

Combustion of Premixed Ammonia and Air Initiated by Spark- Ignited Micro-gasoline-jet in a Constant Volume Combustible Vessel

Investigation of the Effect of Ammonia Addition on the Two-Stage Ignition Process of Dimethyl Ether Based on Chemical Kinetic Analysis

Stage-wise Kinetic Analysis of Ammonia Addition Effects on Two-Stage Ignition in Dimethyl Ether

Shock tube experiments and numerical study on ignition delay times of ammonia/oxymethylene ether-2 (OME 2 ) mixtures

Laser-absorption-spectroscopy-based temperature and NH<sub>3</sub>-concentration time-history measurements during the oxidation processes of the shock-heated reacting NH<sub>3</sub>/H<sub>2</sub> mixtures

Experimental study of the methane/hydrogen/ammonia and ethylene/ammonia oxidation: Multi-parameter measurements using a shock tube combined with laser absorption spectroscopy

An Experimental and Modeling Study on Auto-Ignition of Ammonia in an RCM with N2O and H2 Addition

An experimental and kinetic modeling study on the ignition characteristics of ammonia/ethanol at high temperatures

Numerical Study on the Combustion Properties of Ammonia/DME and Ammonia/DMM Mixtures

A shock tube study of the ignition delay time of DME/ammonia mixtures: Effect of fuel blending from high temperatures to the NTC regime

Investigating Auto-Ignition Characteristics and Kinetic Modeling of NH3/CH4 Mixtures Using an RCM

Experimental and chemical kinetic study for the combustion of ammonia-hydrogen mixtures

Experimental and Kinetic Modeling Study of Laminar Burning Velocity Enhancement by Ozone Additive in NH3 + O-2 + N-2 and NH3 + CH4/C2H6 /C3H8 + Air Flames

Experimental and kinetic modeling study on auto-ignition of ammonia/n-heptane mixtures at intermediate temperatures

Nitromethane as a nitric oxide precursor for studying high-temperature interactions between ammonia and nitric oxide in a shock tube

Experimental and Kinetic Modeling Study of Laminar Burning Velocities of NH3/air, NH3/H2/air, NH3/CO/air and NH3/CH4/air Premixed Flames

Mid-infrared absorption spectroscopy measurements and model improvements during the oxidation of ammonia/ethanol and ammonia/diethyl ether blends in a shock tube

Exploring the Effect of Different Reactivity Promoters on the Oxidation of Ammonia in a Jet-Stirred Reactor

Shock tube and modeling study on autoignition properties of ammonia/diethyl ether mixtures at high temperatures

Experimental and kinetic study on the laminar burning velocities of NH3 mixing with CH3OH and C2H5OH in premixed flames