Abstract:ABSTRACTLarge amount of work has been published on the tacticity‐properties relationship of isotactic polypropylene (iPP). However, the stereo‐defect distribution dependence of morphology and mechanical properties of β‐nucleated iPP (β‐iPP) is still not clear. In this study, two different iPP resins (PP‐A and PP‐B) with similar average isotacticity but different uniformities of stereo‐defect distribution were selected, their β‐iPP injection molding specimens were prepared, and the morphology evolution and tensile behaviors were studied by means of differential scanning calorimetry (DSC), 2D wide‐angle X‐ray diffraction (2D‐WAXD) and scanning electron microscope (SEM). DSC results showed that with the same concentration of β‐nucleating agent (0.3 wt % WBG‐II), PP‐B with more uniform stereo‐defect distribution exhibited more amount of β‐phase than that of PP‐A with less uniform stereo‐defect distribution, indicating that PP‐B is more favorable for the formation of β‐phase. SEM results showed that PP‐B formed more amount of β‐crystals with relatively high structural perfection, while in PP‐A a mixed morphology of α‐ and β‐phase with obviously higher amount of structural imperfection emerges. The results of room‐temperature tensile test indicated that the yield peak width of PP‐B was obviously wider, and the elongation at break of PP‐B was higher than that of PP‐A, showing a better ductile of PP‐B. The morphology evolution results of SEM, 2D‐WAXD and DSC suggest that, a combination of lamellar deformation and amorphous deformation occurred in PP‐A, while only amorphous deformation mainly took place in PP‐B, which was thought to be the reason for the different tensile behaviors of the samples. In the production of β‐PP products via injection molding, the uniformity of stereo‐defect distribution was found to be an important factor. PP with more uniform distribution of stereo‐defect favors the formation of large amount of β‐phase with high perfection, which exhibit superior ductile property. The related mechanism was discussed. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2014, 131, 40027.

Tailoring the mechanical properties of binary polypropylene blends with polymorphic and oriented hierarchical structures

Solvent and solvation effects on reactivities and mechanisms of phospho group transfers from phosphate and phosphinate esters to nucleophiles

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Tailored Structure and Properties of Injection-Molded Atactic Polypropylene/Isotactic Polypropylene Blend

Fabrication of Hierarchically Crystallographic Morphologies in Isotactic Polypropylene

Hierarchical structure and unique impact behavior of polypropylene/ ethylene-octene copolymer blends as obtained via dynamic packing injection molding

Unusual Hierarchical Structures Of Micro-Injection Molded Isotactic Polypropylene In Presence Of An In Situ Microfibrillar Network And A Beta-Nucleating Agent

Efficient Utilization of Atactic Polypropylene in Its Isotactic Polypropylene Blends via “Structuring” Processing

Shear Amplification and Re-Crystallization of Isotactic Polypropylene from an Oriented Melt in Presence of Oriented Clay Platelets

Studies on blends of high-density polyethylene and polypropylene produced by oscillating shear stress field

Self-reinforcing and toughening isotactic polypropylene via melt sequential injection molding

The High Mechanical Properties and Micro-Phase Separation of High Density Polyethylene and Polypropylene Blends

Synergistic Enhancement of Glass Fiber and Tetrapod-Shaped ZnO Whisker on the Mechanical and Thermal Behavior of Isotactic Polypropylene

Investigation on the Tensile Behavior and Morphology Evolution of Isotactic Polypropylene Films Polymerized with Different Ziegler-Natta Catalysts

Relationship Between Mechanical Properties and Crystalline Structure of PPR/iPP Blends Modified with β-Nucleator

Effects of polyolefin elastomer and β-nucleating agent on morphological evolution of isotactic polypropylene under an intensive shear rate

Morphology and mechanical properties of polypropylene/poly (propylene-1-octene) in-reactor alloys prepared by Metallocene/Ziegler-Natta hybrid catalyst

Shear-Induced Fibrillation and Resultant Mechanical Properties of Injection-Molded Polyamide 1010/isotactic Polypropylene Blends

Structure and Properties of Polypropylene Alloy in Situ Blends

Investigation on the Morphology and Tensile Behavior of Β‐nucleated Isotactic Polypropylene with Different Stereo‐defect Distribution

The Morphology Control and Mechanical Properties of High Density Polyethylene and Polypropylene Blend under Oscillating Shear Stress Field