Abstract:Ni-based single crystal line alloy is constituted with gamma phase and gamma' phase in the form of coherency. Since an indenter for two-phase coherent structure is bigger than the usual nano-scale indenter, the press location of indenter may be unclear in nanoindentation simulation. Both gamma phase and gamma' phase may be pressed initially, and the mechanical properties shown are different because of the initial press locations. The nanoindentation of Ni-based single crystal line alloys is simulated by molecular dynamics method. Two models are used to study about the hardness in [001] crystal orientation, one is the model gamma/gamma' with the initial indentation on gamma phase, and the other is the model gamma'/gamma with the initial indentation on gamma' phase. The influence of misfit dislocation at (001) interface on nanoindentation of the two models is analyzed using a center-symmetry parameter. Results show that the misfit dislocation shape of the two models are different after relaxation. Lomer-Cottrell dislocation occurs on (001) interface in the gamma'/gamma model. Before 0.930 nm press depth is reached, there is little change in the (001) interface misfit dislocation of the two models. Relationship between press load and press depth is similar for the two models, and it is the same in the relationship between hardness and press depth. After press depth reaches 0.930 nm, the misfit dislocation at (001) interface for model gamma'/gamma grows big, which results in a smaller press load and a smaller hardness computation in the model gamma'/gamma than that in model gamma/gamma'. When the press depth reach 2.055 nm, we find only a small amount of dislocations in gamma phase that can go into gamma' phase since the misfit dislocation at (001) interface in model gamma/gamma' hinders the process. However, none of dislocations can go into gamma phase because of the prevention caused by Lomer-Cottrell dislocation at the (001) interface in the model gamma'/gamma. That means the Lomer-Cottrell dislocation reinforces the material obviously. So the press load in model gamma'/gamma grows faster than that in model gamma/gamma'.

Parameter Identification and Pileup Behavior of TiAl Alloy Through Nanoindentation and Crystal Plasticity Simulation

Indentation Pileup Behavior of Ti-6Al-4V Alloy: Experiments and Nonlocal Crystal Plasticity Finite Element Simulations

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the 2 phase of TiAl alloy

Experiments and crystal plasticity simulations for the deformation behavior of nanoindentation: Application to the α2 phase of TiAl alloy

Heterogeneous Deformation and Damage Mechanisms in Multi-Phase TA15 Ti-alloy: Insights from Experiments Informed Damage-Crystal Plasticity Modelling

Investigation of the Evolution of Plastic Anisotropy and Pile-up of Al Single Crystal in Nanoindentation Using Different Crystal Plasticity Models

Atomistic Simulation of Nanoindentation on Incipient Plasticity and Dislocation Evolution in Γ/γ′ Phase with Interface and Void

Influence Of Initial Indentation Point On Nanoindentation Of Ni-Based Single Crystal Line Alloys

Combined crystal plasticity simulations and experiments for parameter identification: application to near-β titanium alloy

Molecular dynamics simulation and experimental study on nanoindentation response of polycrystalline γ-TiAl alloy

Nanoindentation simulation study on mechanical properties and microstructure evolution of twin γ-TiAl alloy

Mechanical Characterization and Strain-Rate Sensitivity Measurement of Ti-7333 Alloy Based on Nanoindentation and Crystal Plasticity Modeling

Indentation Creep Surface Morphology of Nickel-Based Single Crystal Superalloys

Experimental and Simulation Analysis of Residual Topography Dominated Deformation Mechanism of Nanoindentation: a Case Study of Inconel 625 Superalloy

Anisotropic Plasticity of Nanocrystalline Ti:A Molecular Dynamics Simulation

Experiments and Crystal Plasticity Finite Element Simulations of Nanoindentation on Ti–6Al–4V Alloy

Influnence of Indenter on the Nanoindentation of Ni Based Single Crystal Alloy

Nanoindentation Simulation of Ni-Base Single-Crystal Superalloy with the Consideration of Interface Effect

An Improved Analytic Model for Extracting Plastic Mechanical Property of Matrix in Hot-Extruded In-Situ TiB2/2024 Composite Based on Berkovich Indentation Experimental Results

Micro- and macroscopic plastic flow responses in high Nb-containing TiAl alloy by nanoindentation

Atomistic simulations of the nanoindentation-induced incipient plasticity in Ni3Al crystal