Abstract:Designing a novel microstructure with higher strength-ductility than lamellar microstructure (LM), which has been considered the most valuable engineering application in the service temperature range, is desired for lightweight TiAl alloys. Our prior publication reported a three-phase tri-modal (T-T) structure for Ti-43.5Al-4Nb-1Mo-0.1B(.at%) with superior mechanical properties than LM at room temperature (Ref: Acta Mater. 225 (2022) 117585). However, its strength-ductility at working temperature has yet to be fully exploited. This work fills the much-needed gap. The qualitative and quantitative optimizations indicate that the T-T structure's yield strength increases first and then decreases with increasing pearlitic-like microstructure (PM, which consist of three-phase (α 2 , γ and β o phase) with clear orientation relationships that form in a lamellar/cellular manner) content while the ductility keeps rising. When the T-T structure contains ∼20% PMs, it exhibits a yield strength about 130 MPa higher than LM coupling with doubled ductility at 750 °C. PMs can induce a prominent twinning induced plasticity and dislocation jog dragging (TWIP&DJD) effect, resulting in better strength-ductility below 700°C; above this temperature, the TWIP&DJD effect significantly plasticizes the alloys. The higher strength of the T-T structure at 750 °C is caused by hetero-deformation-induced strengthening between LMs and PMs, which cannot be offset by the plasticizing caused by PM when the volume fraction of PMs is less than 50%. This study demonstrates that introducing an appropriate amount of plasticizing structures (similar to PM) with excellent work hardening capacity is a promising strategy for enhancing the strength-ductility synergy of TiAl and possibly other brittle materials.

Breaking the Strength–ductility Trade-off in Additively Manufactured Aluminum Alloys Through Grain Structure Control by Duplex Nucleation

Achieving Enhanced Tensile Strength-Ductility Synergy Through Phase Modulation in Additively Manufactured Titanium Alloys

Achieving strength-ductility combination and anisotropy elimination in additively manufactured TiB/Ti6Al4V by in-situ synthesized network architecture with fine grains

Additive manufacturing of titanium alloys with enhanced strength and uniform ductility via multi-element alloying

Simultaneous enhancement of strength and ductility by combining heterogeneous microstructure and nanoprecipitates

Breaking the high-temperature strength-ductility trade-off in TiAl alloys through microstructural optimization

Designing ultra-strong and ductile hierarchical titanium alloys via interstitial solute-mediated multi-morphologic α-nanoprecipitates

Break through the strength-ductility trade-off dilemma in aluminum matrix composites via precipitation-assisted interface tailoring

Introducing β-Ti ductile-zones for enhancing both strength and ductility in heterostructured titanium alloy composites

Strength-ductility synergy in 3D-printed (TiB + TiC)/Ti6Al4V composites with unique dual-heterogeneous structure

Future of the fringe: scenarios for Melbourne's peri-urban growth

Novel approach to additively manufacture high-strength Al alloys by laser powder bed fusion through addition of hybrid grain refiners

Unravelling heterogeneities in sub-grain cellular structure and micromechanical response of additive manufactured Ti-Nb alloys

Acquiring Mg-Ag microalloying TiB 2 /Al-4.5Cu composite simultaneously with ultrahigh strength and ductility via optimized salt-metal reaction and multistage heat treatment

Simultaneously Enhancing the Strength and Ductility of Lamellar Ti–6Al–4V Alloy Via Designing Hierarchical 3D Nanolayered Structure

Toughening the additively manufactured Al alloys via manipulating microstructural heterogeneity

Additive manufacturing of an ultrastrong, deformable Al alloy with nanoscale intermetallics

Bimodal-grain structure enables superior strength-ductility synergy of pure Al

Achieving synergy enhancement of strength and ductility in Ti-6Al-2Sn-4Zr-2Mo-0.1Si alloy by fabricating a new multiscale microstructure

Transport and accumulation of PVP-Hypericin in cancer and normal cells characterized by image correlation spectroscopy techniques.

Multi-scale annealing twins generate superior ductility in an additively manufactured high-strength medium entropy alloy