Abstract:The tensile behavior of Ti6Al4V–5Cu alloy studied in the temperature range of 450–550 °C at the strain rate interval of 10 −3 -10 −1 s −1 . Alloy deformation behavior, microstructure evolution, and its relative internal structure changes due to deformation were investigated. The tensile behavior of the alloy had elucidated in terms of change in true stress-strain relationship. At 450 °C, the alloy showed the decrease of peak stress at the strain rate interval of 10 −3 -10 −2 s −1 , which suggests Ti6Al4V–5Cu plastic flow behavior, was quite different. The alloy exhibited an elongation (El) of 28% at 450 °C in a strain rate of 10 −3 s −1 . At 10 −3 s −1 , the El of the alloy decreased with the increase of forming temperature. However, at 10 −2 s −1 and 10 −1 s −1 , the El increased with the rising of temperature. Scanning electron microscope (SEM) was used to investigate the microstructure of Ti6Al4V–5Cu alloy. The alloy grain boundaries (GBs) were found as continuous and discontinuous structural features, especially the high angle grain boundaries (HAGBs). The GB feature has contributed to the initiation of micro-cracks because of the creation of weakest regions in the material during deformation. The nature of GB geometry has also a tremendous contribution to the workability of Ti6Al4V–5Cu alloy at low forming temperatures. The presence of a high amount (%) LAGBs and the serrated nature of HAGBs structures determined the pull to grain pieces. The deformation mechanism of the Ti6Al4V–5Cu alloy at low forming temperatures was accomplished initially by boundary serration phenomenon due to strain-induced GB migration related to heat treatment at low strain condition, then by initiation of recrystallized grains-triggered by the plasticity behavior of strain induced sub-boundaries, and finally by the development of deformed grains generated by the reduction in corrugation propensity of GBs due to high strain condition.

Influence of Hot-Rolling Deformation on Microstructure, Crystalline Orientation, and Texture Evolution of the Ti6Al4V-5Cu Alloy

Effect of Deformation Temperature on the Microstructure and Texture Evolution of Ti-6Al-4Zr-2Mo-6V Alloy

Hot Deformation Behavior of a Novel Near-β Titanium Alloy Ti-5.5Mo-6V-7Cr-4Al-2Sn-1Fe in (α+β) Phase Region

Microstructure Evolution and Mechanical Properties of a Hot-Rolled Ti Alloy

Microstructure Evolution and Deformation Mechanisms of As-Cast Antibacterial Ti6Al4V-5Cu Alloy for Isothermal Forging Process

Microstructure evolution, tensile properties and internal structure transformation study on Ti6Al4V–5Cu anti-bacterial alloy during uniaxial tensile straining at low forming temperature

Microstructural Development, Deformation Behavior, and Texture Evolution Investigation during Hot Compression of a Dynamically Recrystallized Ti-5Cu Alloy in the Dual (α + β) Phase Region

Effect of Hot Rolling Temperature on Microstructure Evolution, Deformation Texture and Nanoindentation Properties of an Intermetallic Ti-43Al-9V-0.2Y Alloy

Transverse texture weakening and anisotropy improvement of Ti-6Al-4V alloy sheet via asymmetric rolling and static recrystallization annealing

Microstructure and Texture Variations in High Temperature Titanium Alloy Ti65 Sheets with Different Rolling Modes and Heat Treatments

Microstructure evolution, mechanical properties and high temperature deformation of (TiB + TiC)/Ti-3.5Al-5Mo-6V-3Cr-2Sn-0.5Fe titanium alloy

Effect of pack rolling on microstructures and tensile properties of as-forged Ti-44Al-6V-3Nb-0.3Y alloy

Effects of Rolling Deformation on Microstructure and Hardness of Ti-45Al-9Nb-0.3Y Alloy

Evolution of microstructures and properties of Ti-44Al-6V-3Nb-0.3Y alloy after forging and rolling

Mechanical behaviour and microstructural evolution of Ti-6Al-1Mo-1V-2Zr-2Cr-1Fe alloy subjected to hot compression deformation

Texture evolution during multi-pass cold rolling and annealing of Ti-2Al-1.5Mn alloy

Microstructure evolution and recrystallization of Ti6246 alloy in hot‐rolling and annealing processes

Influence of cold rolling deformation on mechanical properties and corrosion behavior of Ti-6Al-3Nb-2Zr-1Mo alloy

Suppression of texture and enhancement of high-temperature tensile property in heavily deformed gradient Ti 2 AlNb alloy

Evolution of Microstructural and Mechanical Properties during Cold-Rolling Deformation of a Biocompatible Ti-Nb-Zr-Ta Alloy

The Influences of Process Annealing Temperature on Microstructure and Mechanical Properties of Near Β High Strength Titanium Alloy Sheet.