Abstract:As the traditional graphite-based composites cannot meet the requirement of rapid developing modern industry, novel sliding electrical contact materials with high self-lubricating performance in multiple environments are eagerly required. Herein a copper-based composite with WS2 and graphite as solid lubricant are fabricated by powder metallurgy hot-pressed method. The friction and wear behaviors of the composites with and without current are investigated under the condition with sliding velocity of 10 m/s and normal load of 2.5N/cm 2 in both air and vacuum. Morphologies of the worn surfaces are observed by optical microscope and compositions of the lubricating films are analyzed by XPS. Surface profile curves and roughness of the worn surfaces are obtained by 2205 surface profiler. The results of wear tests show that the friction coefficient and wear volume loss of the composites with current are greater than that without current in both air and vacuum due to the adverse effects of electrical current which damaged the lubricating film partially and roughed the worn surfaces. XPS results demonstrate that the lubricating film formed in air is composed of oxides of Cu, WS2 , elemental S and graphite, while the lubricating film formed in vacuum is composed of Cu, WS2 and graphite. Because of the synergetic lubricating action of oxides of Cu, WS2 and graphite, the composites show low friction coefficient and wear volume loss in air condition. Owing to the fact that graphite loses its lubricity which makes WS2 become the only lubricant, severe adhesive and abrasive wear occur and result in a high value of wear rate in vacuum condition. The formation of the lubricating film on the contact interface between the brush and ring is one of the factors which can greatly affect the wear performance of the brushes. The low contact voltage drop of the composites in vacuum condition is attributed to the high content of Cu in the surface film. This study fabricated a kind of new sliding electrical contact self-lubricating composite with dual-lubricant which can work well in both air and vacuum environments and provides a comprehensive analysis on the lubrication mechanisms of the composite.

Effect of counterpart materials on tribological behaviors of copper impregnated carbon/carbon composite under electric current condition

Fabrication and tribological behaviors of copper fiber and carbon fiber reinforced phenol‐formaldehyde resin‐based composite for sliding current collector

Tribology performance of Cu-C/C composites with and without current

A comparative investigation into the material matching performance of different friction pairs under current-carrying friction

Effect of Electrical Current on the Tribological Behavior of the Cu-WS 2 -G Composites in Air and Vacuum

Study of Friction and Wear Properties of Cu/Short Carbon Fibers Composites

Friction and Wear Behavior of Copper-Graphite Composite Material in High-Speed Sliding with Current

Enhancement mechanism of carbon fiber on the current-carrying tribological properties of Cf-Al2O3/Cu composites

On the tribological behaviors of Cu matrix composites with different Cu-coated graphite content

Characterization and Tribological Properties of Graphene/Copper Composites Fabricated by Electroless Plating and Powder Metallurgy

Effect of Pyrolytic Carbon Interface Thickness on Conductivity and Tribological Properties of Copper Foam/Carbon Composite

Effect of Electrical Current Density, Apparent Contact Pressure, and Sliding Velocity on the Electrical Sliding Wear Behavior of Cu–Ti3AlC2 Composites

Fabrication and tribological properties of carbon fiber and copper fiber reinforced carbon-based composite by hot pressing

Study on the tribological properties of MoB/Cu laminated composite materials fabricated by hot-pressing process

Comparative study of the current-carrying tribological properties of carbon graphite composites with different hardnesses

Study on the Tribology Properties of the Particles/Cu Composite Coatings

Influences of B 4 C and carbon nanotubes on friction and wear performance of Cu base self-lubricating composite

Study on the Tribological Performance of Copper-Based Powder Metallurgical Friction Materials with Cu-Coated or Uncoated Graphite Particles as Lubricants

Research on Synergistic Lubrication Effect of Silver Modified Cu–Ni-graphite Composite

Comparative Study on Wear Behaviors of Metal-Impregnated Carbon Material and C/C Composite Under Electrical Sliding