Abstract:The optimal design of microstructure is the key to further improve the properties of particle reinforced metal matrix composites. In this study, in-situ TiB2 and TiC + TiB2 reinforced Cu matrix composites are used as examples to develop the microstructure-based representative volume element models to describe their damage evolution and strengthening mechanisms. The most critical features including size distribution and morphology of the particles as well as the fracture of metal matrix, brittle damage of ceramic particles and traction-separation debonding of the interface were integrated into the modeling. Simulation results show that the model could well predict the performance of the composite and reveal its damage mechanism. When the particle size is normally distributed, the composite exhibits higher strength due to the size effect of different particles, which is more consistent with the experimental result. Both matrix and ceramic particles in mixed-phase particle reinforced metal matrix composites can be subjected to higher stresses, which results in higher strength of (TiC + TiB2)/Cu composites. Additionally, the spherical TiC particles facilitate the relaxation of stress concentration within the composite, resulting in a synergistic enhancement of strength and ductility. Under compression, localized interface damage first appears around the sharp corners of the hexagonal particles and induces crack initiation toward the matrix. These microcracks are interconnected and propagate along the direction of high stress, eventually leading to the failure of the composite. This work provides the basis and new ideas to reveal the failure mechanism of composites and further optimize their configuration design.

Formulation for Zirconia Toughened Alumina (ZTA) Reinforced Metal Matrix Composites Based on a Three-Phase Concentric Inclusion Model

A numerical study of the mechanical and fracture properties of ZTA(Zirconia toughened alumina)p/40Cr steel spatial spherical dot matrix composite

Modeling Method of C/C-ZrC Composites and Prediction of Equivalent Thermal Conductivity Tensor Based on Asymptotic Homogenization

Preparation and Properties of ZTA + WC Particles/Hypereutectic High Chromium Cast Iron Composites

Wearing and interfacial characterization of zirconia toughened alumina reinforced high chromium cast iron composites in an actual working condition

The constitutive model and processing map for in-situ 5wt% tib2 reinforced 7050 al alloy matrix composite

Effect of quenched-tempered heat treatment on the wear resistance mechanism of zirconia toughened alumina ceramic reinforced high chromium cast iron architecture composite

Interfacial Bonding And Abrasive Wear Behavior Of Iron Matrix Composite Reinforced By Ceramic Particles

The Fabrication and Properties of Particle Reinforced Cast Metal Matrix Composites

Experimental Investigation and Modelling of Hot Forming B4C/AA6061 Low Volume Fraction Reinforcement Composites

Investigation of Multi-Phase Intermetallic Matrix Composites (IMC) Based on Al–Mo–Zr–Co System

Insight into the Microstructure Configuration and Strengthening Mechanisms of a Cast In-Situ Al3Zr Reinforced Al–Li Matrix Composite

Dimensioanl Stability of TiC Particle Reinforced ZA43 Matrix Composite

Compression Performance and Abrasive Wear Resistance of CuNi‐Modified Zirconium Oxide‐Toughened Alumina Particles‐Reinforced Iron Matrix Composites

The Α Phase Recrystallization Mechanism and Mechanical Properties of a Near-Α Titanium Matrix Composite

Strengthening mechanism of load sharing of particulate reinforcements in a metal matrix composite

Microstructure and Mechanical Properties of Fe Matrix Composites Reinforced by Nickel–chromium Double-Layer Coated ZTAP Ceramics

The Structure of Al_3Ti and Reinforcing Mechanism in Composite Al_3Ti/ZL101

Microstructure and mechanical properties of in-situ nitride-reinforced refractory high-entropy alloy TiZrHfNbTa matrix composites

Three-body Abrasive Wear Resistance of Iron Matrix Composites Reinforced with Ceramic Particles

Numerical modeling and failure evolution of microstructure-based in-situ TiB2 and TiC+TiB2 reinforced Cu matrix composites