Abstract:This Letter proposes an approach to develop a spoof surface plasmon polariton (SSPP) transmission line (TL) by loading short-circuited (SC) shunt stubs. Lower out-of-band rejections can be flexibly controlled without affecting the upper cutoff frequency by independently modifying the stubs. Dispersion analysis of the SSPP unit is realized by theoretical calculation and circuit simulation to predict the upper cutoff frequency of the proposed SSPP TL simultaneously. Also, parametric sweeping of the SC shunt stubs is performed based on circuit simulation to investigate their impacts on the lower and upper out-of-band rejections of the proposed SSPP TL. In addition, electric field distributions of different types of TLs are simulated and compared to study the transmission characteristics of the proposed SSPP TL. The lower cutoff frequency can be flexibly tuned in a wide range, from 1.2 to 2.1 GHz, in the simulations. The measured 3-dB fractional bandwidth is about 128.1%, covering a range from 1.19 to 5.43 GHz. The numerical and experimental results are compatible, which verifies the feasibility of the proposed approach. This approach can offer more convenience and flexibility for controlling the rejections of the SSPP by introducing up to four tuning parameters. More importantly, the proposed SSPP TL avoids using the substrate integrated waveguide (SIW) technique, which shows the potential to decrease the transverse width ( 0.44 λ g ), especially at lower frequencies (e.g., 1.2 GHz), and to reduce the complexity in designing the high-efficiency transition. This work paves the way for the development of novel SSPP-based microwave devices.

Capacitor-Loaded Coplanar Waveguide Spoof Surface Plasmon Polariton with Reduced Transversal Width

Spoof Surface Plasmon Polaritons Developed from Coplanar Waveguides in Microwave Frequencies

Compact CPW Spoof Surface Plasmon Polariton Transmission Line with Interdigital Structure

Spoof Surface Plasmon Polaritons Based on Balanced Coplanar Stripline Waveguides

Spoof Surface Plasmon Polariton Transmission Line with Reduced Line‐width and Enhanced Field Confinement

Spoof Surface Plasmon Polaritons Transmission Lines with Line‐width Reduction Based on Miniature Unit Structures

Mush-Room Structures–Loaded Coplanar Waveguide Spoof Surface Plasmon Polariton with Reduced Longitudinal Length

Capacitor-Loaded Spoof Surface Plasmon for Flexible Dispersion Control and High-Selectivity Filtering

Compact Spoof Surface Plasmon Polariton Waveguides with Simple Configurations and Good Performance

Capacitor-Loaded Spoof Surface Plasmon (SSP) for Flexible Dispersion Control and High-Selectivity Filtering

An Ultra-Compact Surface Plasmon Transmission Line Based on Partially Grounded Coplanar Waveguide

Spoof Surface Plasmonic Waveguide Devices with Compact Length and Low-Loss

Single-Conductor Spoof Surface Plasmon Polaritons Transmission Line with Bandpass Feature Based on Embedded Cross-Shaped Resonators

Wideband Miniaturized Design of Complementary Spoof Surface Plasmon Polaritons Waveguide Based on Interdigital Structures

A New Design For Spoof Surface Plasmon Polaritons Using Periodic Holes Etched On The Stripline

An Ultra-Thin Coplanar Waveguide Filter Based on the Spoof Surface Plasmon Polaritons

A Compacted 2.5-Dimensional Spoof Surface Plasmon Polaritons Transmission Line

Short-circuited Stub-Loaded Spoof Surface Plasmon Polariton Transmission Lines with Flexibly Controllable Lower Out-of-band Rejections

Strongly Confined Spoof Surface Plasmon Polaritons Waveguiding Enabled by Planar Staggered Plasmonic Waveguides

Highly-Confined and Low-Loss Spoof Surface Plasmon Polaritons Structure with Periodic Loading of Trapezoidal Grooves

Surface Plasmon Transmission Line Based on Folded Stepped Grooves and Spiral-Shaped Structures