Abstract:Atmospheric plasma sprayed (APS) thermal barrier coatings (TBCs) with lamellar structure exhibit low thermal conductivity and low stiffness. However, high temperature exposure for certain long duration causes the sintering which heals two-dimensional (2D) inter-lamellar pores and intrasplat pores. Such sintering effect increases the stiffness and thermal conductivity of the coatings and consequently reduces the stability and durability of TBCs. It can be expected that large 2D pores with a wide opening is difficult to be eliminated. In this study, inter-lamellar 2D pores with large opening width were fabricated in the La2Zr2O7 (LZO) coatings through spraying LZO+SrO coatings and removing the SrO splats in the water. Then, the conventional LZO coating and the porous LZO coating were subjected to high temperature exposure in the air at 1300 °C for different durations. The microstructure evolution especially in terms of the shape and density of inter-lamellar 2D pores was examined. In addition, the change of thermo-physic properties and the mechanical properties of the coatings with increasing exposure duration were studied. Results show that the 2D pores in LZO coating created by those SrO splats inherit primarily large opening width from 200nm to about 1 µm which endows the LZO coating with high sustainability at high temperature environment. Under thermal exposure at 1300oC, it was found that 2D pores resulting from SrO splats are free from healing while conventional 2D inter-lamellar pores with small opening width formed during splat cooling became healed rapidly. Thus, thermal conductivity and Young's modulus of the conventional LZO coating increased rapidly, while unhealed 2D pores in the highly porous LZO coatings contributed to the low Young's modulus and low thermal conductivity of LZO coating with remarkably high stability. With addition of 30% SrO in spray powder, a LZO coating with a thermal conductivity of about 0.39 W.m-1.K-1 in the as-prepared state was obtained. The coating maintained a thermal conductivity of 0.57 W.m-1.K-1 even after 100 hours exposure at 1300°C. The present results indicated that high sintering-resistant thermal barrier coating can be fabricated though designing inter-lamellar 2D pores with large opening width in the coating by the present novel approach.

Tailoring Sintering-Resistant Thermal Barrier Coatings by Considering Critical Healing Width of Two-Dimensional Interlamellar Pores

A matching design co-enhancing thermal barrier and thermal cyclic performances of sintering-resistant coatings

Scale-progressive Healing Mechanism Dominating the Ultrafast Initial Sintering Kinetics of Plasma-Sprayed Thermal Barrier Coatings

A comprehensive sintering mechanism for thermal barrier coatings‐Part III: Substrate constraint effect on healing of 2D pores

Durable TBCs with Self-Enhanced Thermal Insulation Based on Co-Design on Macro- and Microstructure

High Sintering-Resistant Plasma-Sprayed Thermal Barrier Coatings Designed with Large Two-Dimensional Inter-Lamellar Pores

Tailoring degradation-resistant thermal barrier coatings based on the orientation of spontaneously formed pores: From retardation to self-improvement

Strain/sintering Co-Induced Multiscale Structural Changes in Plasma-Sprayed Thermal Barrier Coatings

Achieving Self-Enhanced Thermal Barrier Performance Through a Novel Hybrid-Layered Coating Design

Constrained Healing and Morphology Change Mechanism of 2D Cracks in Plasma Sprayed Thermal Barrier Coatings

A Comprehensive Mechanism for the Sintering of Plasma-Sprayed Nanostructured Thermal Barrier Coatings

High Heat Insulating Thermal Barrier Coating Designed with Large Two-Dimensional Inter-lamellar Pores

Multi-Scale Multi-Points Inter-Splat Connection Enhanced Sintering Model for Plasma-Sprayed Lamellar TBCs

Failure Mechanism and Cracking-Resistant Design of Thermal Barrier Coatings with Long Life Span

Sintering resistance of advanced plasma-sprayed thermal barrier coatings with strain-tolerant microstructures

Improve durability of plasma-splayed thermal barrier coatings by decreasing sintering-induced stiffening in ceramic coatings

Achieving high anti-sintering performance of plasma-sprayed YSZ thermal barrier coatings through pore structure design

Dominant effects of 2D pores on mechanical behaviors of plasma sprayed ceramic coatings during thermal exposure

Low-thermal-conductivity thermal barrier coatings with a multi-scale pore design and sintering resistance following thermal exposure

Influence of Pores on the Thermal Insulation Behavior of Thermal Barrier Coatings Prepared by Atmospheric Plasma Spray

Multiscale Pores in TBCs for Lower Thermal Conductivity