Abstract:Vinyl chloride/ N-phenylmaleimide copolymer ( VC/PMI) and vinyl chloride/ N-phenylmaleimide/ acrylonitrile terpolymer (VC/PMI/AN) were synthesized in the suspension copolymerization process for improving the heat resistance of poly( vinyl chloride) PVC) This paper emphasized on the studies on the characterization of the heat resistant properties of these three co) polymers mainly by means of dynamic mechanical experiment with the change of storage modulus ( E'), change rate of E' with temperature and mechanical loss factor ( tandelta) near the glass transition. The Vicat softening point ( VSP) was also tested supplementally for comparison. The lower the change rate of E' with temperature is, the higher the heat resistance of VC/PMI and VC/PMI/AN will be. The effects of the amount of PMI and AN in the recipes of copolymerization on the change rate of E' with temperature, tandelta and VSP were also investigated. The results show that the increase of the amount of PMI will increase the rigidity of the backbone of the copolymer chain so as to improve the heat resistance. On the other hand, the introduction of AN into the copolymer will give more uniform distribution of PMI unit or segment in the backbone, and thus improves the heat resistance of the copolymer further. It is discovered that there are two peaks of mechanical loss or two glass transition temperatures of VC/PMI/AN copolymerization product. It may be interpreted from the higher reactivities of PMI and AN than VC. During the copolymerization process of VC, PMI and AN, the more active PMI and AN will copolymerize more rapidly and will consume entirely at conversion of about 45% similar to 50%. Thereafter, VC continues to homopolymerize to form PVC homopolymer until a final conversion of 85%. Actually, the final product is a mixture of VC/PMI/AN terpolymer and homo-PVC, showing two T(g)s.

Comparison of toughening effects of several common toughening agents and polycarbonate-polydimethylsiloxane block copolymer on polyvinyl chloride

Excellent toughness of rigid polyvinylchloride at low temperature improved by polycarbonate‐polydimethylsiloxane block copolymer

Research on Toughening Modification of Copolymerized Polypropylene Using Polyolefin Elastomers

Toughening of PBT/PC Blends with Core-Shell Modifier

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Studies on Mechanical and Rheological Properties of Poly(Vinyl Chloride) Modified with Elastomers and Rigid Organic Particles

Study of Poly(vinyl Chloride)/acrylonitrile–styrene–acrylate Blends for Compatibility, Toughness, Thermal Stability and UV Irradiation Resistance

Cervical Dilatation in Spontaneous and Induced Labours

Synergistic Effect of Polycarbonate on Reactive Core-Shell Particles Toughened Poly (butylene Terephthalate)

Synthesis of ACR/nanometer SiO2 Composite Particles and Their Tonghening Effect on PVC

Synthesis of ACR Impact Modifier with PVC Shell and Its Toughening Efficiency on PVC

Toughening of PBT by POE/POE-g-GMA Elastomer Through Regulating Interfacial Adhesion and Toughening Mechanism

Study on the fusion properties of extruded foaming rigid PVC

Polycarbonate blends with high environmental stress crack resistance, high strength and high toughness by introducing polyvinyl butyral at small fraction

The Crystallinity of Pvc and Its Effect on Physical Properties

Heat Resistant Properties of Vinyl Chloride-N-Phenylmaleimide (-Acrylonitrile) Suspension Polymerized Copolymer

Variation of core-shell structural particles and their toughening behavior in poly (vinyl chloride) (PVC) matrix

Study on Toughening Mechanism of Low Molecular Weight PC/PP Blend

Toughening PET/PC Blends with Ethylene-propylene-diene Rubber

Phase Separation of Impact‐modified PVC/PMMA Blends under Melt‐blending Conditions