Abstract:The emerging market for consumer electronics and electric vehicles has stimulated intensive research on lithium metal batteries (LMBs) with high energy densities and large cycle lifetimes. A metallic Li anode has a high theoretical specific capacity of 3860 mAh.g(-1) and lowest redox potential of -3.04 V (vs. the standard hydrogen electrode) and is generally considered an ideal electrode for next-generation high-energy-density LMBs. However, their deployment in practical batteries is severely hindered by the formation of unsafe dendrites and fast capacity decay due to the uncontrollable formation of fragile solid electrolyte interfaces (SEls). Herein, we describe the stable cycling of carbon paper (Cp)-supported Li-Sn alloy anodes in carbonate electrolytes modified with 1 mol.L-1 bis(2,2,2-trifluorotoluene) carbonate (DTFEC). The molten Li-Sn alloy with 8% (mass fraction) Sn was synthesized through thermal treatment at 400 degrees C in an atmosphere of Ar. The Li-Sn-alloy-coated carbon paper (SnLi/Cp) was obtained after the molten alloy was conformally loaded onto the surface of a carbon paper under the action of capillarity. The as-synthesized interconnected SnLi/Cp composite was characterized by X-ray diffraction, energy-dispersive spectrometry, and scanning electron microscopy. The porous SnLi/Cp composite consisted of only Li and Sn5Li22 phases supported by the mechanically strong carbon paper with a good conductivity; no impurity was observed in the XRD results. The synergy of the DTFEC additive and alloying with Sn provided composite anodes with significantly improved rate capability and remarkable stability owing to the formation of a dense fluorinated SEI layer with high mechanical strength and ion penetration. Moreover, with the porous SnLi alloy covered by a fluorinated protection layer, lithium avoids the intrinsic issues of uncontrollable volume expansion and dendrite growth, which restrict the practical application of Li metal, exhibiting a stabilized over-potential of only 90 mV after 100 cycles at 8 mA.cm(-2). Notably, stable cycling with a 12 mu L lean electrolyte was also observed at 5 mA.cm(-2). Overall, the prototype full cell assembled with the SnLi/Cp anode and NMC811 cathode exhibited a high Coulombic efficiency (98.1%) and remarkable cycling stability for 300 cycles at 1C (1.5 mA.cm(-2)). The rate capability was evaluated at various rates of 0.5C to 5C. Compared to pure Li, the SnLi/Cp anode in the full cell exhibited a higher capacity, particularly at a high rate (similar to 126 mAh.g(-1 )at 5C). Our approach provides integrated Li metal electrodes with effectively improved cycle stabilities and is very attractive for practical high-energy-density lithium batteries.

Reconstruction of Solid Electrolyte Interphase with SrI2 Reactivates Dead Li for Durable Anode‐Free Li‐Metal Batteries

A Bifunctional Composite Artificial Solid Electrolyte Interphase for High Stable Solid-State Lithium Batteries

Engineering Wavy‐Nanostructured Anode Interphases with Fast Ion Transfer Kinetics: Toward Practical Li‐Metal Full Batteries

Dendrites‐Free Lithium Metal Anode Enabled by Synergistic Surface Structural Engineering

High Interfacial-Energy Interphase Promoting Safe Lithium Metal Batteries.

Implantable Solid Electrolyte Interphase in Lithium-Metal Batteries

Modulating the Inner Helmholtz Plane towards Stable Solid Electrolyte Interphase by Anion‐π Interactions for High‐Performance Anode‐Free Lithium Metal Batteries

A Salt‐in‐Metal Anode: Stabilizing the Solid Electrolyte Interphase to Enable Prolonged Battery Cycling

A Sustainable Solid Electrolyte Interphase for High‐Energy‐Density Lithium Metal Batteries under Practical Conditions

LiBr–LiF‐Rich Solid–Electrolyte Interface Layer on Lithiophilic 3D Framework for Enhanced Lithium Metal Anode

A Solution‐Processable High‐Modulus Crystalline Artificial Solid Electrolyte Interphase for Practical Lithium Metal Batteries

Improvement In Performance Of Three-Dimensional Snli/Carbon Paper Anode In Lean Electrolyte With In Situ Fluorinated Protection Layer

Electrochemical Activation of Ordered Mesoporous Solid Electrolyte Interphases to Enable Ultra‐Stable Lithium Metal Batteries

Enhanced Salt Content and Stabilized Bilayer Passivation Interphase Toward Long-Life and High-Safety Anode-Free Lithium Battery

In-situ constructed polymer/alloy composite with high ionic conductivity as an artificial solid electrolyte interphase to stabilize lithium metal anode

Reactivating Dead Li by Shuttle Effect for High-Performance Anode-Free Li Metal Batteries

A Li2CO3 sacrificial agent for anode-free lithium metal batteries

Bi-containing Electrolyte Enables Robust and Li Ion Conductive Solid Electrolyte Interphase for Advanced Lithium Metal Anodes

Constructing an Inorganic-Rich Solid Electrolyte Interphase by Adjusting Electrolyte Additives for Stable Li Metal Anodes

Interficial Engineering of Lithium Metal Anode for Sulfide Solid State Batteries

Superior Lithium-Metal All-Solid-State Batteries with In-situ formed Li 3 N-LiF-rich Interphase