Design, Manufacture, and Cryogenic Testing of a Linerless Composite Tank for Liquid Hydrogen

Robin Olsson,Christopher Cameron,Florence Moreau,Erik Marklund,Matthias Merzkirch,Jocke Pettersson
DOI: https://doi.org/10.1007/s10443-024-10219-y
IF: 2.3
2024-03-19
Applied Composite Materials
Abstract:This paper describes design, manufacture, and testing of a linerless composite vessel for liquid hydrogen, having 0.3 m diameter and 0.9 m length. The vessel consists of a composite cylinder manufactured by wet filament winding of thin-ply composite bands, bonded to titanium end caps produced by additive manufacturing. The aim was to demonstrate the linerless design concept with a thin-ply composite for the cylinder. The investigation is limited to the internal pressure vessel, while real cryogenic tanks also involve an outer vessel containing vacuum for thermal insulation. Thermal stresses dominate during normal operation (4 bar) and the layup was selected for equal hoop strains in the composite cylinder and end caps during filling with liquid hydrogen. Two vessels were tested in 20 cycles, by filling and emptying with liquid nitrogen to 4 bar, without signs of damage or leakage. Subsequently, one vessel was tested until burst at almost 30 bar.
materials science, composites
What problem does this paper attempt to address?
The main problem that this paper attempts to solve is to design, manufacture and test a unlined composite tank for storing liquid hydrogen. Specifically, the goal of the research is to demonstrate the design concept of manufacturing unlined tanks using thin - layer composites and verify their performance under actual working conditions. The following is a detailed explanation of the main problems in the paper: ### Research Background and Motivation 1. **Hydrogen as a Future Aviation Fuel** - Hydrogen is regarded as a potential non - fossil fuel for future aircraft due to its high energy density, in order to address climate change and carbon dioxide emission problems. - In order to minimize the volume of the hydrogen storage tank in the aircraft, hydrogen needs to be stored in liquid form at a temperature of - 253°C (20K) and a pressure of 4 bar. - Liquid hydrogen has been used in space launchers since the 1960s, but its research in the aerospace field began shortly after World War II. 2. **Design Challenges of Hydrogen Storage Tanks** - Metal hydrogen storage tanks have problems of relatively large weight and hydrogen embrittlement, especially for long - term use in civil aircraft. - Carbon fiber polymer composites are the preferred materials for lightweight hydrogen storage tanks. - Unlined composite tanks (Type V) can avoid the problems of weight increase and thermal expansion mismatch caused by the liner. ### Research Objectives 1. **Design and Manufacture** - Design and manufacture a unlined composite tank with a diameter of 0.3 meters and a length of 0.9 meters. - The tank is made of wet - wound thin - layer composite tapes, and the two ends are connected by additively - manufactured titanium alloy end caps. 2. **Testing** - Conduct 20 cycle tests on the tank, filling and emptying liquid nitrogen to 4 bar each time, and no damage or leakage was found. - Subsequently, a burst test was carried out on one of the tanks until the pressure was nearly 30 bar. ### Main Technical Problems 1. **Thermal Stress** - Under normal operating conditions (4 bar), thermal stress is the main source of stress. - Select a composite laminate structure so that the composite cylinder and the end cap have equal circumferential strain when filled with liquid hydrogen. 2. **Material Properties** - The composite is made of TeXtreme® thin - layer unidirectional tapes produced by Oxeon Company, with a thickness of 0.050 mm, and the actual wound thickness is about 0.10 mm. - The mechanical properties and thermal expansion coefficients of the material at room temperature and - 253°C were tested and corrected in detail. 3. **Manufacturing Process** - Use the wet - winding technique to manufacture the composite cylinder. - Produce titanium alloy end caps by additive manufacturing technology to ensure that the end caps will not become the weak links of the structure. 4. **Bonded Joints** - The bonded joint between the composite cylinder and the titanium alloy end cap is a key point in the design. - Evaluate the stress distribution of the bonded joint under thermal stress and internal pressure by finite element analysis (FEA) to ensure its safety. ### Conclusion This paper demonstrates the feasibility and advantages of this design in liquid hydrogen storage through the design, manufacture and testing of unlined composite tanks. The research results show that through the rational selection of materials and the optimization of the design, unlined composite tanks can operate safely and reliably under actual working conditions.