Abstract:The current high volume of plastic waste, but low recycling rate, has led to environmental pollution and wasted energy. Greenhouse gas CO2 can facilitate thermal cracking to dehydrogenate waste plastics, and has potential value for producing olefins. In this work, the pyrolysis properties of low-density polyethylene (LDPE) were studied by thermogravimetric analysis and Py-GC/MS. The effect of the pyrolysis atmosphere, using N2 or CO2, with various MCM-41 catalyst ratios on pyrolysis product distribution, were investigated. The experimental results show that the olefin selectivity under a N2 atmosphere was from 30.32 % to 44.66 % which increased as the MCM-41 catalyst was increased. Under a CO2 atmosphere, the olefin selectivity reached a maximum of 60.39 %. The Boudouard reaction was also enhanced by the introduction of CO2. The carbon content of the subdivided olefins showed that in CO2, the promotion of C5-C12 olefins was relatively weak when non-catalyzed or at low catalytic ratios, but increased significantly at higher MCM-41 catalyst ratios. With a ratio of LDPE: MCM-41 = 5:4, the CO2 atmosphere showed the greatest promotion of C5-C12 olefins over N2, with an increase of 14.66 % compared to N2, representing a 48.54 % yield of the liquid product. Producing C5-C12 olefins under these conditions maximized energy efficiency. These results show that catalytic pyrolysis of LDPE under a CO2 atmosphere has great potential to produce C5-C12 olefins, which can be used to produce high-value chemicals such as naphtha and gasoline. This opens new opportunities for the chemical recycling of plastic waste.

Evolution of Light Olefins During the Pyrolysis of Polyethylene in a Two-Stage Process

Pyrolysis of Polyolefins Using Rotating Arc Plasma Technology for Production of Acetylene

Analysis on low-temperature polyethylene pyrolysis and gasification in different atmospheres

Characteristics of a new type continuous two-stage pyrolysis of waste polyethylene

Gas Production from Polyethylene Terephthalate Using Rotating Arc Plasma

Molecular-level kinetic modelling for the pyrolysis of high-density polyethylene in a two-stage process

Continuous flow pyrolysis of virgin and waste polyolefins: a comparative study, process optimization and product characterization

Pyrolysis of long chain hydrocarbon-based plastics via self-exothermic effects: The origin and influential factors of exothermic processes

Kinetics, Product Evolution, and Mechanism for the Pyrolysis of Typical Plastic Waste

Characteristics of Pyrolyzing Polyethylene in a Horizontal Plasma Jet Reactor

Production of C5-C12 olefins by catalytic pyrolysis of low-density polyethylene with MCM-41 in CO2/N2

Microwave-assisted pyrolysis of low-density polyethylene (LDPE)to value-added products over HY, HZSM-5 and Hβ catalyst

Simulating Polyethylene Pyrolysis from a Generalized Molecular-Level Kinetic Model

Analysis of liquid products and mechanism of thermal/catalytic pyrolysis of HDPE

Investigating Kinetic Behavior and Reaction Mechanism on Autothermal Pyrolysis of Polyethylene Plastic

The Effects of Polyolefin Structure and Source on Pyrolysis-Derived Plastic Oil Composition

Comparative Study on the Synergistic Co-Pyrolysis of Plastics and Rubber Waste: Thermal Behavior and Product Distributions

Efficient Pyrolysis of Low-Density Polyethylene for Regulatable Oil and Gas Products by ZSM-5, HY and MCM-41 Catalysts

Co-pyrolysis of pinewood and HDPE: pyrolysis characteristics and kinetic behaviors study

Thermal Degradation of Waste Medical Masks to Light Olefins in a Two-Stage Process

Analysis and Control of Products Obtained From Pyrolysis of Polypropylene Using A Reflux Semi-batch Reactor and GC-MS/FID and FT-ICR MS