Abstract:Li–CO2 batteries have recently attracted attention as promising candidates for next-generation energy storage devices due to their extremely high theoretical energy density. The real application of Li–CO2 cells involves addressing several drawbacks, including high charging potential, poor coulombic efficiency, and low rechargeability. Molybdenum disulfide supported on carbon nanotubes (MoS2/CNT) with various ratios functioned as a cathode catalyst for Li–CO2 batteries. The optimal MoS2/CNT composite achieved a maximum discharge capacity of 8551 mAh g–1 with a coulombic efficiency of 96.7%. This hybrid also obtained an initial charging plateau of 3.87 V at a current density of 100 mA g–1 with a cutoff capacity of 500 mAh g–1. It provided ideal electrochemical stability of 142 cycles at the current densities of 100 mA g–1, which was comparable with that of some precious metal catalysts. This optimized MoS2/CNT was also cycled at 200 and 400 mA g–1 for 112 and 55 times, respectively. Density functional theory calculations demonstrated that the sulfided Mo-edge (s-Mo-edge) on MoS2 materials showed appropriate adsorption strengths of Li, CO2, and Li2CO3. Moreover, joint results of Raman profiles and extended X-ray absorption fine structure spectra elucidated that the catalytic efficiencies of MoS2/CNT hybrids were proportional to the quantities of exposed s-Mo-edge active sites.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsami.0c17942?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsami.0c17942</a>.Computational method; XPS spectra of bare MoS2 and MoS2/CNT catalysts (Figure S1); full discharge–charge profiles of bare CNT and bare MoS2 cathodes (Figure S2); SEM with elemental mapping spectra of bare MoS2 and MoS2/CNT catalysts (Figure S3); electrochemical impedance spectroscopy of bare MoS2 and MoS2/CNT cathodes (Figure S4); cycling performances of bare CNT, MoS2/CNT, and MoS2-CNT cathodes (Figure S5–S7, S9); photograph and XRD diagrams of electrodes after the cycling measurement (Figure S8); high-resolution Mo 3d XPS spectrum of MoS2/CNT cathode (Figure S10); calculated adsorption energies of Li, CO2, and Li2CO3 on different sites of MoS2 (Figure S11–S13); charge density difference of CO2 on different sites of MoS2 (Figure S14); comparisons of electrochemical performances with previous studies (Table S1); and fitting parameters for Mo EXAFS spectra (Table S2) (<a class="ext-link" href="/doi/suppl/10.1021/acsami.0c17942/suppl_file/am0c17942_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Engineering the Interfacial Orientation of MoS2/Co9S8 Bidirectional Catalysts with Highly Exposed Active Sites for Reversible Li-CO2 Batteries.

Energy Band Engineering Guided Design of Bidirectional Catalyst for Reversible Li-CO2 Batteries.

Energy Band Engineering Guided Design of Bidirectional Catalyst for Reversible Li–CO 2 Batteries

Mild Oxidation Regulating the Surface of Mo 2 CT X MXene to Enhance Catalytic Activity for Low Overpotential and Long Cycle Life Li-CO 2 Batteries

Crystalline molybdenum carbide−amorphous molybdenum oxide heterostructures: In situ surface reconfiguration and electronic states modulation for Li−S batteries

Porous Mo3P/Mo Nanorods as Efficient Mott‐Schottky Cathode Catalysts for Low Polarization Li‐CO2 Battery

Steering the Orbital Hybridization to Boost the Redox Kinetics for Efficient Li-CO2 Batteries

Rational design of hollow flower-like MoS2/Mo2C heterostructures in N-doped carbon substrate for synergistically accelerating adsorption-electrocatalysis of polysulfides in lithium sulfur batteries

Regulating Electrocatalytic Polysulfides Redox Kinetics through Manipulating Surface Electronic Structure of Molybdenum-Based Catalysts for High-Performance Lithium-Sulfur Batteries

Revealing the role of crystal structure to catalysis: Inverse spinel phase Co-Mn-based catalyst for Li-S batteries

Catalytically Active Site Identification of Molybdenum Disulfide as Gas Cathode in a Nonaqueous Li–CO 2 Battery

Nanofibrous Cathode Catalysts with MoC Nanoparticles Embedded in N-Rich Carbon Shells for Low-Overpotential Li-CO2 Batteries.

Construction of MnS/MoS2 heterostructure on two-dimensional MoS2 surface to regulate the reaction pathways for high-performance Li-O2 batteries

Activating MoS 2 Nanoflakes via Sulfur Defect Engineering Wrapped on CNTs for Stable and Efficient Li‐O 2 Batteries

Mo2C-MoP heterostructure regulate the adsorption energy of electrocatalysts in high-performance Li-S batteries

MoO 2 /t-C 3 N 4 Heterogeneous Materials with Bidirectional Catalysis for the Rapid Conversion of S Species in Li-S Batteries

Understanding the Dual-phase Synergy Mechanism in Mn2O3-Mn3O4 Catalyst for Efficient Li-CO2 Batteries.

Tailoring Li2CO3 Configuration and Orbital Structure of CoS to Improve Catalytic Activity and Stability for Li‐CO2 Batteries

Porous Mo<sub>3</sub>P/Mo Nanorods as Efficient Mott-Schottky Cathode Catalysts for Low Polarization Li-CO<sub>2</sub> Battery

Three-Dimensional Carbon-Supported MoS2 with Sulfur Defects As Oxygen Electrodes for Li-O2 Batteries

Heterostructure Mo2C/α-MoO3/G Catalyst Based Heterogeneous Catalysis/deposition Mechanism for High-Performance Li-S Battery