Abstract:PurposeThe positioning accuracy of each component is important to ensure the image quality of cone‐beam CT. However, accurate positioning is not easy and requires experience and time. The option is to calibrate the geometric parameters and then plug them into a reconstruction algorithm which is the preferred solution in practice. In this case, the image quality is determined by the accuracy and precision of the calibration method. This work describes a method to independently calibrate an imaging system in each pose (projection angle) for a cone‐beam CT with a nonideal circular trajectory.MethodsThe calibration method uses a phantom with 12 beads on 2 planes that are observed on the radiographic images. This pose‐independent calibration method (PIC) can decorrelate the relationships among the geometric parameters so that the parameters can be estimated one‐by‐one. This simplifies the calibration process. Besides the pose‐independent calibration method, this paper also describes an extended calibration method with additional constraints on the system geometry. Both methods are validated with numerical simulations and then experimentally on a practical system with a scanning object loosely supported by rotating wheels. The object rotates during the CT data acquisition. The angular and pose information of the CT system are not accurately known a priori in this case.ResultsThe numerical simulations and the experiments both provide satisfactory results. The relative error of the calibrated source‐to‐detector distance in the simulation is less than 0.1%. The errors in the calibrated roll, pitch, and yaw angles are less than 0.04°. A sensitivity study using various bead position uncertainties in random directions shows that the pose‐independent calibration method is robust to measurement errors. Tests were also done with a nonideal circular trajectory for further validation. Images reconstructed using the geometric parameters from both the pose‐independent and the extended calibration methods were free of artifacts and blur from misalignment. All these results demonstrate the effectiveness of these methods.ConclusionsThe PIC method can be used to independently calibrate the geometric parameters of a cone‐beam CT view‐by‐view. Thus, the PIC method can be implemented on commonly used systems such as circular, nonideal circular or C‐arm cone‐beam CTs. The PIC method can also be useful for some irregularly configured CT systems to fulfill special imaging requirements, for example, a CT system when the x ray source or the rotating platform cannot be easily located. The PIC method will reduce the costs of ensuring very precise mechanics and the labor in fine tuning CT systems.

Least Squares Based Geometric Error Measurement for Sparse View CT: a 2D Simulation Study

Geometric Artifact Correction for Symmetric Multi-Linear Trajectory CT: Theory, Method, and Generalization

Sparse-view CT reconstruction method for in-situ non-destructive testing of reinforced concrete

Analytical Geometric Parameter Calibration Algorithm for Cone-Beam CT

Full-scale Measurement of CNC Machine Tools

Geometric Constraints Enable Self-Supervised Sinogram Inpainting in Sparse-View Tomography

Evaluation of sparse-view reconstruction from flat-panel-detector cone-beam CT.

Fast Detection of Geometric Errors for Three-Axis Machine Tools with Combined Double-Ball Bars Based on Spatial Circle Detection

Investigations into the Geometric Calibration and Systematic Effects of a Micro-CT System

Study of System Matrix Based Reconstruction for Uncertain Scanning Track CT

A SVD-based Method to Assess the Uniqueness and Accuracy of SPECT Geometrical Calibration.

The realisation of fast X-ray computed tomography using a limited number of projection images for dimensional metrology

Geometry parameter estimation for sparse X-ray log imaging

Geometry Calibration Method for a Cone-Beam CT System.

Error and limit determination for dimensional measurements of thin-walled structures with industrial computed tomography

An interval subdividing based method for geometric calibration of cone-beam CT

Helical CT Reconstruction from Sparse-view Data through Exploiting the 3D Anatomical Structure Sparsity

An Automatic Regularization Method: An Application for 3-D X-Ray Micro-CT Reconstruction Using Sparse Data

A Novel Calibration Method Incorporating Nonlinear Optimization and Ball‐bearing Markers for Cone‐beam CT with a Parameterized Trajectory

Ultrasparse View X-ray Computed Tomography for 4D Imaging

Geometry-Aware Attenuation Learning for Sparse-View CBCT Reconstruction