Abstract:As a very promising additive manufacturing (AM) technique, selective laser melting (SLM) has gained considerable attentions due to the feasibility of producing light-weight metallic components directly from virtual design data. On the other hand, high strength, low density and high corrosion resistance Ti-6Al-4V alloy has been a preferred AM used material for the aviation and military industries. However, the fatigue damage behaviors of SLMed or AMed components usually suffer from interior defects such as incomplete fusion and gas pores due to unstable process or unsuitable processing parameters. Therefore, thorough investigations on process-induced and metallurgical defects and its influence on the fatigue behavior is required for robust designs and engineering applications of high performance SLM components. As an advanced characterization approach, synchrotron radiation micro computed X-ray tomography (SR -mu CT) has been recently to investigate the fatigue damage behaviors of critical components with defects. Based on self-developed in situ fatigue testing rig fully compatible with the BL13W1 at Shanghai Synchrotron Radiation Facility (SSRF), several AMed specimens were prepared for in situ fatigue SR - mu CT. The Feret diameter and extreme values statistics were then adopted to characterize the defect size, morphology, population, location and the influence on fatigue life. Fatigue fractography was also examined to further identify the defect to really initiate a fatigue crack. Results show that two types of defects including gas pores and the lack of fusion can be clearly distinguished inside SLM Ti-6Al-4V alloys. Fatigue crack with a typical semi-ellipse usually initiates from the defects at the surface and near the surface. Besides, the defects less than 50 mu m and sphericity of 0.4 similar to 0.65 dominate for the SLM Ti-6Al-4V alloys. It is also found that the larger the characteristic size of the defect, the lower the fatigue life. Current results can provide a theoretical basis and support to predict the fatigue performance of SLM Ti-6Al-4V alloys. Further investigations should be performed on the relationship between the critical defect and fatigue strength by introducing the Kitagawa-Takahashi diagram.

Anisotropic High Cycle Fatigue Property Estimation for Laser Additive Manufactured Ti6Al4V Alloy Dependence on Tomographic Imaging of Defect Population

X-ray imaging of defect population and the effect on high cycle fatigue life of laser additive manufactured Ti6Al4V alloys

Fatigue of Laser Powder-Bed Fusion Additive Manufactured Ti-6Al-4V in Presence of Process-Induced Porosity Defects

Effect of Defects on High Cycle Fatigue Property of Selective Laser Melted Ti6Al4V Alloy

An Investigation of the Anisotropic Fatigue Properties of Laser Additively Manufactured Ti-6Al-4V under Vibration Loading

A New Approach to Correlate the Defect Population with the Fatigue Life of Selective Laser Melted Ti-6Al-4V Alloy

Low-cycle Fatigue Behavior and Life Prediction of TA15 Titanium Alloy by Crystal Plasticity-Based Modelling

The effect of defect population on the anisotropic fatigue resistance of AlSi10Mg alloy fabricated by laser powder bed fusion

Investigation of the Effect of Artificial Internal Defects on the Tensile Behavior of Laser Powder Bed Fusion 17–4 Stainless Steel Samples: Simultaneous Tensile Testing and X-Ray Computed Tomography

Residual Stress and Long Fatigue Crack Growth Behaviour of Laser Powder Bed Fused Ti6Al4V: Role of Build Direction

Detectability by X-ray micro computed tomography of fatigue initiating void defects in laser powder-bed additively manufactured Ti-6Al-4V coupons

Defect Induced Fatigue Behaviors of Selective Laser Melted Ti-6Al-4V Via Synchrotron Radiation X-Ray Tomography

Effects of Post-Processing and Loading Orientation on High-Cycle Fatigue of Selective Laser Melted Ti-6Al-4V

Effects of Build Direction and Heat Treatment on the Defect Characterization and Fatigue Properties of Laser Powder Bed Fusion Ti6Al4V

Rotating bending fatigue mechanisms of L-PBF manufactured Ti-6Al-4V alloys using in situ X-ray tomography

The Role of Microstructure and Local Crystallographic Orientation Near Porosity Defects on the High Cycle Fatigue Life of an Additive Manufactured Ti-6Al-4V

Understanding the fatigue behaviour of Ti–6Al–4V manufactured via various additive processes

Overload-induced anisotropy of fatigue crack growth in laser deposited Ti-6Al-4V alloy

Microstructure and Low-Cycle Fatigue Performance of Selective Electron Beam Melted Ti6Al4V Alloy

Analysis of Room-Temperature/High-temperature High-Cycle Fatigue Performance of Laser Additive Manufactured Ti65 Titanium Alloy

Numerical Investigation of the Influence of Fatigue Testing Frequency on the Fracture and Crack Propagation Rate of Additive-Manufactured AlSi10Mg and Ti-6Al-4V Alloys