Abstract:The geometric parameters of the deposited layer include the width, height, and penetration depth of the deposited layer. The welding current, wire feeding speed, and torch travel speed during the additive manufacturing process of TC4 titanium alloy have the greatest impact on the geometric parameters of the deposited layer. In order to study how the deposition layer width, deposition layer height, and penetration depth are affected by the welding current, wire feeding speed, and torch travel speed, this article uses Design Expert 8.0.6 software for Box−Behnken design response surface experiments. During the experimental design, the welding current, wire feeding speed, and torch travel speed are used as input variables. The deposition layer width, deposition layer height, and penetration depth are selected as the responses. We designed 17 response surface experiments that were conducted using GTAW-AM. The results show that as the welding current increases, the penetration depth and width of deposition layer gradually increase, and the deposition layer height gradually decreases. As the wire feeding speed increases, the deposition layer height and penetration depth gradually increase, and the wire feeding speed has a minimal effect on the deposition layer width. As the torch travel speed increases, the penetration depth, width and height of deposition layer gradually decrease. The response surface method experimental design can also optimize the matching of three process parameters: welding current, wire feeding speed, and torch travel speed, thereby obtaining the optimal matching range of process parameters. Within the optimized matching range of process parameters, a welding current of 90 A, a wire feeding speed of 900 mm/min, and a torch travel speed of 200.18 mm/min were selected to prepare TC4 titanium alloy thin-walled part. The microstructure of the top, middle and bottom are all basketweave structure. The α phase gradually becomes coarse from the top to the bottom. The microhardness of the top, middle, and bottom of the thin-walled parts is 362.7 HV, 352.7 HV, and 340.5 HV, respectively. The horizontal tensile strength is 926.1 MPa, with an elongation of 12.22%, and the vertical tensile strength is 938.1 MPa, with an elongation of 14.41%.

Regulation of the Robotic Gas Tungsten Arc Additive Repair Process for Thin-Walled Variable-Width Components

Impact of Process Parameters on Forming Quality and Deposition Efficiency of Unsupported Rods in Wire Arc Additive Manufacturing

Study of the Mechanism of a Stable Deposited Height During GMAW-Based Additive Manufacturing

Feedback control of variable width in gas metal arc-based additive manufacturing

Effect of molten-pool inertia in variable-width arc-based direct energy deposition by regulating parameters

The Effects of Processing Parameters during the Wire Arc Additive Manufacturing of 308L Stainless Steel on the Formation of a Thin-Walled Structure

Fused Plus Wire Arc Additive Manufacturing Materials and Energy Saving in Variable-Width Thin-Walled

Effects of Heat Input on Morphology of Thin‐Wall Components Fabricated by Wire and Arc Additive Manufacturing

Laser direct metal deposition of variable width thin-walled structures in Inconel 718 alloy by coaxial powder feeding

Process Planning Strategy for Wire-Arc Additive Manufacturing: Thermal Behavior Considerations

An Innovative Methodology in Narrow Gap GTAW for Alternating Magnetic Field with Synchronous Swing of Filler Wire and Arc

Optimization of TIG arc additive process of AZ91 magnesium alloy based on layer width control

Wire Arc Additive Manufactured Radial Thin Wall: Fabrication Strategy, Macroscopic Defect Control, Microstructure, and Mechanical Properties

Microstructures and Mechanical Properties of Wire Arc Additive Manufactured 5183-Al: Influences of Deposition Dimensions

Development of a New Cold Metal Transfer Arc Additive Die Manufacturing Process

Effects of Processing Parameters on Molten Behavior, Arc Stability, and Defect Forming in Swing-Arc Narrow Gap GMA Vertical Up Welding

Multi-layer Deposition Mechanism in Ultra High-Frequency Pulsed Wire Arc Additive Manufacturing (WAAM) of NiTi Shape Memory Alloys

Technology-Based Recontouring of Blade Integrated Disks After Weld Repair

Study on the Relationship between Process Parameters and theFormation of GTAW Additive Manufacturing of TC4 Titanium Alloy Using the Response Surface Method

A New Method for Refinement of Ti-6Al-4 V Prior-Β Grain Structure in the Alternating Magnetic Field Assisted Narrow Gap Gas Tungsten Arc Welding (AMF-GTAW) Via Filler Wire Oscillation

Forming characteristics of additive manufacturing process by twin electrode gas tungsten arc