Abstract:The effect of high temperature heat treatment on the tribological behavior of carbon/carbon (C/C) composites has been investigated. C/C composite preforms were made from 1K PAN plain carbon cloth, and densified using rapid directional diffusion (RDD) CVI processes. Four specimens treated at 1800, 1800+2000, 2000, and 2300°C, respectively, were prepared. A ring-on-ring specimen configuration was used to simulate aircraft brakes. The brake initial angular velocity ranged from 1800 to 7500 rpm (6.2–26.0 m s−1 average linear sliding velocity). The specific pressure and moment of inertia were 392–784 kPa and 0.25–0.31 kg m2, respectively (1.9–42.3 MJ m−2 kinetic energy loading per unit friction surface area). The results showed that the stability of the brake moment–time curves increased with increasing heat treatment temperature (HTT) for the four composites, and those treated at 2300°C possessed the lowest initial brake moment peak ratio values (from 1.1 to 1.3). The high degree of graphitization and low shear forces of the matrix carbon resulting from the high HTT could allow friction films to develop and reduce those values under the present brake conditions. The friction coefficients of four RDD CVI C/C composites decreased with an increase in specific pressure. The resulting changes in the friction coefficient of the four composites due to the specific pressure changes have basically nothing to do with the interface temperature under those conditions. According to the practical brake conditions, the friction properties of RDD CVD C/C composites could be improved by regulating the structure of the brake discs, changing the specific pressure exerted on the discs and the heat treatment. The linear wear rates of the four materials increased with increasing HTT. The composites treated at 2000°C had both high enough friction coefficients and the lower linear wear rates. The different heat treatment methods at 2000°C had no obvious effect on the friction and wear properties of RDD CVI C/C composites.

Influence of High Temperature Treatment of C/C Porous Preform on Friction and Wear Behavior of C/C-SiC Composites

Influence of pyrolytic carbon interphase and pyrolysis temperature on the mechanical and tribological properties of Cf/SiC after heat treatment at 1800 °C

Effect of Pyrocarbon Content on Thermal and Frictional Properties in C/C Preforms of C/C–SiC Composites

Mechanical and tribological properties of C/C–SiC ceramic composites with different preforms

Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

Tribological Properties of Carbon Fiber Toughened SiC Prepared by Hot Pressing Sintering

Preparation and Properties of C/SiC Composites Reinforced by High Thermal Conductivity Graphite Films

EFFECT OF HEAT TREATMENT TEMPERATURE ON THE TRIBOLOGICAL PROPERTIES OF CARBON FIBER REINFORCED CARBON COMPOSITES

Influence of High-Temperature Oxidation and Test Conditions on the Dynamic Mechanical Properties of 2.5D SiCf/SiCm Composites

Water-Lubricated Friction Properties of C/C-SiC Composites with Different SiC-Phase Contents Fabricated by RMI

Preparation and Friction Properties of SiC-Al2O3/2A50 Co-Continuous Composites

Effect of SiC on the anti-ablation resistance and flexural strength of (Hf-Ta-Zr)C-C/C composites

Effect of Pyrocarbon Content in C/C Preforms on Microstructure and Mechanical Properties of the C/C–SiC Composites

Mechanical and ablation properties of 3D orthogonal woven C/C-SiC composite based on high-solid-loading slurry impregnation

Design and Optimization of the Coating Thickness on Chopped Carbon Fibers and Sintering Temperature for ZrB2-SiC-C-f Composites Prepared by Hot Pressing

Effect of heat treatment on the tribological behavior of 2D carbon/carbon composites

Wear behavior of SiC nanowire-reinforced SiC coating for C/C composites at elevated temperatures

Microstructure, Mechanical and Ablation Properties of Transpiration Cooling Applied to C/C-SiC Composite for Novel Anti-ablation Material

Static friction properties of carbon/carbon composites

Effects of SiC Content on the Mechanical and Thermophysical Properties of 3D Cf/SiC–Al Composites

EFFECT OF C/C POROUS PREFORM ON THE MICROSTRUCTURE AND FLEXURAL STRENGTH OF C/C-SiC COMPOSITES