Abstract:A steel-wire wound reinforced thermoplastic pipe (SWW-RTP) has been widely utilized in many industrial areas, and a soil landslide is an inevitable hazardous extreme condition for the SWW-RTP as it is usually buried underground. It is imperative to study the mechanical failure behavior and the failure criterion of the SWW-RTP under the combination of internal pressure and soil landslide conditions, and this paper is the first study to investigate the topic. In this paper, groups of stress-strain curves of high-density polyethylene (HDPE) and steel wires were obtained by uniaxial tensile tests at different strain rates, with the help of a Digital Image Correlation device (DIC). A rate-dependent constitutive model was employed to represent the mechanical behavior of the HDPE and to help deduce the stress-strain curve of the HDPE under the required strain rate, estimated from the static simplification of the dynamic soil landslide. Afterwards, a finite element model of the SWW-RTP, embedded in a cubic of soil, was established with the software ABAQUS. The SWW-RTP model was composed of HDPE solid elements, embedded with steel-wire truss elements, and the soil was characterized with the extended Drucker-Prager model. A quartic polynomial displacement distribution was applied to the soil model to represent the soil landslide. Then, the mechanical response of the SWW-RTP was analyzed. It was found that the failure criterion of the HDPE yield was more suitable for the pipe subjected to internal pressure and soil landslide conditions, instead of the steel-wire strength failure criterion always used in traditional research on the SWW-RTP. Further, the influence of landslide width, internal pressure and steel-wire number were discussed. The larger the width of the landslide area, the gentler the deformation of the pipeline; this resulted in an increase in the maximum landslide and a decrease in the maximum curvature with the width of the landslide area. The relatively high internal pressure was beneficial to the safety of the SWW-RTP under landslide, because the internal pressure could increase the stiffness of the pipeline. The number of steel wires had a limited influence on the maximum landslide required for the SWW-RTP's failure. This work can be useful for the design and safe assessment of the SWW-RTP under internal pressure and soil landslide conditions.

Wet Collapse Mechanism of Steel-Reinforced Flexible Pipe Structures under Curvature Effect: Physical Experimentation and Numerical Simulation

Numerical Study of CFRP-Bonded Pressure Pipes Subject to Impact Load

Short-Term Mechanical Analysis of Polyethylene Pipe Reinforced by Winding Steel Wires Using Steel Wire Spiral Structural Finite Element Model

Buckling Stability of Steel Strip Reinforced Thermoplastic Pipe Subjected to External Pressure

Flexible Pipes: Influence of the Pressure Armor in the Wet Collapse Resistance

Plastic Limit Load Analysis for Pressure Pipe with Incomplete Welding Defects Based on the Extended Net Section Collapse Criteria

Mechanical Responses of Metallic Strip Flexible Pipe Subjected to Combined Bending and External Pressure

Local buckling of deepwater oil-gas pipeline under high hydrostatic pressure

On Collapse Failure Analysis Of Subsea Corroded Sandwich Pipelines Under External Pressure

Experimental and analytical evaluation of the performance of hybrid steel-CFRP pipelines at high external pressures

Research On Safety Assessment Method For Pressure Pipe With Incomplete Welding Defects Under Complicated Loadings

Study on Mechanical Failure Behavior of Steel-Wire Wound Reinforced Thermoplastic Pipe under Combined Internal Pressure and Soil Landslide Conditions

Numerical and Experimental Study on Balanced Performance and Axial Stiffness of Fiber-Reinforced Rubber Pipe

An analytical approach for assessing the collapse strength of an unbonded flexible pipe

Behaviour of reinforced thermoplastic pipe under combined bending and external pressure

Theoretical Modeling Of Steel Strip Reinforced Flexible Pipe With Swaging End Fitting By Taking Into Account Stress Concentration Effect

On Elastic-Plastic Collapse of Subsea Pipelines under External Hydrostatic Pressure and Denting Force

Mechanical Behaviors Of Steel Strip Reinforced Flexible Pipes Under Bending

On the Collapse of Thick-Walled Pipes with Corrosion Defects under External Pressure

Collapse of pipes with non-uniform corrosion defects under external pressure: A reverse inversion modeling method

Collapse of reinforced thermoplastic pipe (RTP) under combined external pressure and bending moment