Abstract:In-service magnetorheological (MR) dampers inevitably experience degradations and such changes would directly impair their expected control effects. Currently, detection of cable MR damper failures are offline approaches, which necessitates removing dampers from cables and conducting manual inspection or lab testing. Recently developed machine vision technology offers a new approach for non-contact observations of cable vibration displacements. However, due to the limited view range of monocular camera device, it is usually impractical to measure full-scale cable vibration displacements with satisfied accuracy. Therefore, a novel method is proposed in this paper for in-situ detection of cable MR damper failures using cable substructure vibration displacements under unknown wind loads. First, a small section of stay cable equipped with an MR damper is extracted as the target substructure for identification, enabling a monocular machine vision to accurately observe its vibration displacements. The unknown MR damper force and interface forces of the cable substructure are treated as unknown inputs to the substructure. Then, the unknown wind loads on the substructure are modeled as random walk processes and incorporated into the substructural augmented state. Since only partial cable displacements of the substructure are measured, the smoothing minimum variance unbiased (MVU) filter without direct feedthrough is used to simultaneously identify substructural augmented state, MR damper force and interface forces. In this way, cable MR damper failures can be detected based on the hysteretic loop constructed by the identified substructural displacements and MR damper force as damper with different failures would exhibit distinct hysteretic loop characteristics. Detections of three typical failure models of in-service cable MR dampers are investigated respectively in the numerical validations and the identification results are in consistent with those by previous offline experimental tests, which verify the proposed method for the in-situ detection of cable MR damper failures.

Two-step Online Identification of In-Service Cable-Inertial Mass Damper Systems under Nonstationary Wind Excitations

In-situ Detection of Cable MR Damper Failures Using Cable Substructure Vibration Displacements under Unknown Wind Loads

Damping identification using weighted fitting of Frequency-response-function (WFF) method

Experimental Evaluation of an Inertial Mass Damper and Its Analytical Model for Cable Vibration Mitigation

Wide-area Time-delay Robust Damping Control Based on System Identification

A Multi-Task Learning-Based Automatic Blind Identification Procedure for Operational Modal Analysis

Various damper forces and dynamic excitation nonparametric identification with a double Chebyshev polynomial using limited fused measurements

Spectral Analysis of a Sagged Cable with an Optimal Viscous Inertial Mass Damper under Random Wind in a Generalized State-Space Formulation

A Novel Eddy Current Damper System for Multi-Mode High-Order Vibration Control of Ultra-Long Stay Cables

Damping of a Stay Cable with Two Eddy‐current Inertial Mass Dampers: Theoretical Analysis, Experimental Study, and Parameter Optimization

An Identification Method for Damping Ratio of in Situ Building

System Identification of a Structure Equipped with a Cable-Bracing Inerter System Using Adaptive Extended Kalman Filter

Bayesian Time Domain Approach for Damping Identification and Uncertainty Quantification in Stay Cables Using Free Vibration Response

Automatic identification of structural modal parameters based on density peaks clustering algorithm

Monitoring-based identification of nonlinear aerodynamic damping in multi-mode vortex-induced vibrations of a stay cable

Stochastic Optimization of Electromagnetic Inertial Mass Dampers in Nonlinear Hybrid Base Isolation Systems Under Seismic Excitations

A State Space Technique for Modal Identification of Coupled Structure–tuned Mass Damper Systems from Vibration Measurement

Simultaneous Identification of Stiffness, Mass, and Damping Using an On-Line Model Updating Approach

Experimental Investigations on Effectiveness of Viscous and Viscous Inertial Dampers on Reducing the Multimodal Vibrations of Stay Cables

Application of stochastic subspace identification for stay cables with an alternative stabilization diagram and hierarchical sifting process

Simulation Study of Semi-Active Control of Stay Cable Using MR Damper under Wind Loads