Abstract:In recent years, the rapidly growing consumption of fossil fuels negatively affects the environment and public health has attracted much attention. Much effort has been made to find a clean and renewable alternative energy. Bio-oil, produced by flash pyrolysis, is one of the more encouraging products for valorisation of biomass. It has been identified as a promising alternative energy source for fossil fuel owing to its outstanding characteristics such as higher energy density, more suitable for storage and transportation, less capital investment than any other products of biomass. However, the nature of bio-oil contains high acidity, strong corrosiveness, low heating value, thermal instability and chemical complexity, which severely restrict its wide range of applications as a high quality energy. Therefore, it is necessary to upgrade bio-oil. The upgrading techniques include steam reforming, esterification, emulsification, hydrodeoxygenation, catalytic pyrolysis etc. In this paper, catalytic pyrolysis experiments were performed in a fixed bed with inner diameter of 16mm and height of 380mm for bio-oil model compounds (diacetone alcohol, furfural, ethyl acetate and guaiacol) over different characteristics zeolites (HY, HZSM-5, ZSM-5, P/ZSM-5, La/ZSM-5, Ni/ZSM-5) at the condition of T=400℃, WHSV=4 h-1. The catalysts physical properties were investigated by BET (Brunauer-Emmett-Teller surface area) analyse. Water content was detected by using the method of Karl Fischer (870 KF Titrino). The GC-MS was used to analyze the major constituents of the pyrolytic products qualitatively and quantitatively. After the addition of La, the pore size increased from 0.61 nm (ZSM-5) to 0.89 nm (La-ZSM-5). On the contrary, the pore size of P modified ZSM-5 is 0.49 nm which is smaller than that of ZSM-5. The pyrolytic products of the model compounds included organic fraction, water, coke and gas. Compared with ZSM-5,the coke deposition over the La modified ZSM-5 decreased from 2.61% to 1.99% and the organic fraction increased dramatically from 46.10% to 61.51%, which showed the best performance in terms of products distribution among all modified catalyst. The conversions of overall model components and single model component were calculated respectively. The difficulty of the model components pyrolysis is guaiacol>furfural>ethyl acetate>diacetone alcohol. By adding catalysts, the conversion of totally compounds were increased in different degrees, which meaned zeolite promoted the degree of catalytic pyrolysis. HZSM-5 had a best catalytic pyrolysis activity with the highest totally compounds conversion rate of 65.98%. There was a slight decline in the conversion of model compounds contrasted ZSM-5 with La/P/Ni modified ZSM-5. The major components of catalytic pyrolysis were aromatic hydrocarbons, ketones, phenols and so on. It means that a series of decarboxylation and decarbonylation reactions were taken place during the pyrolysis process. On the one hand, the reduction of the oxygen content of bio-oil help to improve its stability, on the other hand it will enhance its heating value. The optimal selectivity of aromatic reached 7.36% over HZSM-5. The La modified ZSM-5 improved the selectivity of aromatic from 6.72%to 7.28%. The highest yield of saturated alcohol was 7.1%over ZSM-5 and decreased using modified ZSM-5. According to the catalytic pyrolysis products distribution, the different reaction pathways for model compounds were discussed, which provided a theoretical basis for experimental study of upgrading bio-oil.

Study on the Prepared Bio-Oil by Catalytic Hydrothermal Liquefaction of Antibiotic Residues in Ethanol-Water Reaction System with Transition Metal Modified HZSM-5

Online upgrading of bio-oil with alkali-treated HZSM-5 zeolites

Catalytic Hydrothermal Liquefaction of Penicillin Residue for the Production of Bio-Oil over Different Homogeneous/Heterogeneous Catalysts

Preparation and Properties of Bio-Oil from the Antibiotic Residue by Hydrothermal Liquefaction

Upgrading Phenolic Compounds and Bio-Oil Through Hydrodeoxygenation Using Highly Dispersed Pt/TiO2 Catalyst

Co-hydrotreating of Used Engine Oil and the Low-Boiling Fraction of Bio-Oil Blends for the Production of Liquid Fuel

Study on hydrothermal liquefaction of antibiotic residues for bio-oil in ethanol-water system

Study on the hydrothermal liquefaction of antibiotic residues with molecular sieve catalysts in the ethanol–water system: focus on product distribution and characterization

Effect of Fe, Ni, and Co on the hydrothermal liquefaction of Chinese herb residue for bio-oil production

Catalytic pyrolysis of bio-oil model compounds over La/P/Ni modified ZSM-5

Catalytic upgrading of penicillin fermentation residue bio-oil by metal-supported HZSM-5

Co-cracking of Bio-Oil Model Compound Mixtures and Ethanol over Different Metal Oxide-Modified HZSM-5 Catalysts

Microwave-assisted pyrolysis of waste cooking oil for hydrocarbon bio-oil over metal oxides and HZSM-5 catalysts

Hydrocarbon-Rich Bio-Oil Production from Ex Situ Catalytic Microwave Co-Pyrolysis of Peanut Shells and Low-Density Polyethylene over Zn-Modified Hierarchical Zeolite

Catalytic Hydrothermal Liquefaction for Bio-Oil Production over CNTs Supported Metal Catalysts

Hydrothermal Liquefaction of Cd-enriched Amaranthus Hypochondriacus L. in Ethanol–water Co-Solvent: Focus on Low-N Bio-Oil and Heavy Metal/metal-Like Distribution

Improvement of Properties of Bio-Oil from Biomass Pyrolysis in Auger Reactor Coupled to Fluidized Catalytic Bed Reactor

Preparation of bio-oils by hydrothermal liquefaction (HTL) of penicillin fermentation residue (PR): Optimization of conditions and mechanistic studies

Improved hydrodeoxygenation of bio-oil model compounds with polymethylhydrosiloxane by Brønsted acidic zeolites

Bio-oil upgrading at ambient pressure and temperature using zero valent metals

Preparation of rich hydrocarbon biofuels from cracking of waste cooking oil by CaO@Zn-KIT-6