Abstract:The copper crystal cone-shaped micro-nanostructure is used as the substrate, and the Ni-W alloy layer and Au nanolayer are plated sequentially. Instantaneous soldering with lead-free solder is realized under ultrasonic assistance at room temperature. This solves the residual stress and thermal damage caused by high melting point lead-free solder on thin chips and thermal components, and ensures the safety and reliability of electronic components. Copper-based microstructures are deposited by electrochemical methods. An amorphous Ni-W alloy layer with a thickness of 180 nm is deposited on the Cu-based microstructures by adjusting the atomic ratio of the plating solution. The Ni-W layer is further coated with a 50 nm Au layer to prevent oxidation. Solid-phase transient soldering is realized by combining the Au/Ni-W multilayer thin-film-modified Cu substructures with commercial solder (SAC305) for a holding time of 3 s at a soldering pressure of 10,000 gf (20 MPa) while ultrasonically assisted. The soldered samples are aged at 180 °C for 10 min, 30 min, and 60 min, respectively. Copper substructures with different surface modifications are subjected to destructive shear experiments with solder balls. Scanning electron microscope and X-ray fluorescence thickness gauge are used to study the microstructure, intermetallic compound (IMC) composition thickness and properties of the soldered interface and section. The cone height of the Cu-based structure is 2-4 μm, and the diameter of the bottom is 800 nm-1200 nm, which has a sharp tip and an excellent L/D ratio. The interface between the Au/Ni-W modified Cu substructure and the solder ball is almost free of holes. The average shear strength at the soldering interface is about 43.06 MPa. The fracture surface after the shear experiment basically occurs inside the solder ball matrix, which belongs to the pure toughness fracture. The interface between the Au/Ni-W-modified Cu-based structure and the solder ball is subjected to long aging treatment at 180 °C. The soldering interface showed a "bright layer". New phases are generated on the solder side above the "bright layer", while no new phases appear on the Cu substructure side below the "bright layer". The copper-based microstructure is inserted into the inside of the solder ball to form an inlay and produce mechanical interlocking. Au/Ni-W alloy modification layer can effectively improve the surface hardness of copper-based structures. This creates a large hardness difference with soft solder and enables the formation of fewer holes in the insertion solder. Amorphous Ni-W alloys are prone to form dense oxide films during ultrasonication. The Au film modification prevents oxide generation and increases the average shear strength of the soldering interface. The Ni-W alloy layer retards the interdiffusion between Cu-Sn, blocks the excessive growth of Cu-Sn IMCs, and reduces the reliability problems caused by interface failure.

The Influence of Solder Oxidation on Low-Temperature Solid-State Bonding Based on Ni Micro-Nano Cones

Effect Of Solder Alloy Composition On Its Solid-State Bonding Quality With Ni Microcones

Low-temperature Solid State Bonding Method Based on Surface Cu–Ni Alloying Microcones

Influence of Bonding Conditions on Low-temperature Solid-state Bonding of Cobalt Based Nanocones

Low-Temperature Solid State Bonding of Sn and Nickel Micro Cones for Micro Interconnection

Electroless Silver Coating on Copper Microcones for Low-Temperature Solid-State Bonding

Low-Temperature Bonding Method Based on Metallic Microcone Array for Interconnection Application

Low Temperature Bonding Method Using Cu Micro Cones

Low Temperature Bonding with Metallic Micro-Cones for 3D Integration

Micro-cones Cu fabricated by pulse electrodeposition for solderless Cu-Cu direct bonding

Solid-state Bonding Using Metallic Cone Layer for Interconnection

Solid-phase transient soldering method based on Au/Ni-W multilayer thin-film-modified copper-based structures

Effects Of Ni-W(Au) Coated Cu Microcones On The Bonding Interfaces

Anti-oxidation Property of Nanotwinned Copper Micro-Cone Array for Low-Temperature Bonding

Low-temperature attaching of LED chips using SnBiIn solder nanoparticles

Study on Low-Temperature Bonding and Reliability of Nano-Twin Copper Micro-Cone Array

An Investigation Of The Influence Of Nickel Particles On Interfacial Morphology Of Substrate-Solder Couple

Interfacial morphologies and possible mechanisms of a novel low temperature insertion bonding technology based on micro-nano cones array

Study of Diffusion Mechanism in Low-Temperature Bonding Method Based on Surface Cu Microcones

In-situ investigation on melting characteristics of 1D SnCu alloy nanosolder

A Low-Temperature Solid-State Bonding Method Based on Copper Bump Coated with Nickel Microcones and Silver Buffer