Abstract:Siloxanes are widely used in different applications: health care, dry cleaning, household products, paints and coatings, paper, personal care, for example. This explains their prevalence in the environment. Because of their volatile nature, most of the time they are dispersed in the atmosphere, but they can also be present in the slurry from landfills. During anaerobic digestion, when the temperature goes up to 60 degrees C, siloxanes are volatilized, forming part of the biogas. Operational problems using biogas to produce energy, heat and hydrogen have been identified. At high temperatures the siloxanes are transformed into silicate dioxide (commonly called sand transmission). These white deposits may adhere to metal or catalytic substrate surfaces, seriously reducing equipment efficiency, and this can be a reason for changing equipment warranties. Consequently, elimination of siloxanes has become very important. Unfortunately, relatively little information can be found on this subject. Nevertheless some authors have described different analytical methods for siloxane quantification, and recent studies have looked at the presence of siloxanes in landfills and the restriction on the energy recovery equipment using the biogas produced. The growing consumption of siloxanes and silicones in industrial processes consequently increase their prevalence in the environment, hampering the use of biogas as a source of 'green energy'. Therefore, the principal focus of this study is the treatment of siloxanes. Their elimination was carried out using an adsorption process with four different porous materials: activated carbon cloths (ACC), granular activated carbon (GAC), zeolite and silica gel. Two representative siloxane compounds were used in this study, hexamethyldisiloxane (L2) and octamethylcyclotetrasiloxane (D4). Adsorption kinetics and isotherms in batch reactors were performed. It was observed that the mass transfer into the porous material was more rapid for the activated carbon than for the zeolite and silica gel, congruent with the porous structure of the material. Moreover, it was found that D4 is more adsorbable than L2, due to possible interactions between the solid surface and the physical structure of the cyclic compound (D4). The influence of humidity and temperature were also studied. The increase in the temperature reduced the adsorption capacities. The influence of humidity on the adsorption was investigated under dry air and humid air at 70%. No significant difference in the adsorption capacities was found for the activated carbon and for the zeolite, but for the silica gel the mass transfer decreased considerably. For the adsorption isotherms, the maximal capacity of elimination was obtained with the activated carbon materials and was directly related to the porous structure. Thus activated carbon cloth was chosen to design the adsorption-desorption processes in a dynamic system. Thermal heating was used to achieve the regeneration process. Initial cycles have been accomplished and show the stability of the process.

Copper Oxide Modified Activated Carbon for Enhanced Adsorption Performance of Siloxane: an Experimental and DFT Study

Surface Modification of Activated Carbon for Siloxane Adsorption

Modified Mesoporous Silica For Efficient Siloxane Capture

Siloxane D4 adsorption by mesoporous aluminosilicates

Preparation of Organically Functionalized Silica Gel As Adsorbent for Copper Ion Adsorption

Highly efficient super activated carbon supported ultra-low loading copper catalyst for the oxidative carbonylation of methanol to dimethyl carbonate

A facile method to fabricate AC/CuO for efficient removal of organic pollutants by adsorption and persulfate-based advanced oxidation processes

Experimental and DFT study on the adsorption of VOCs on activated carbon/metal oxides composites

Strengthened removal of emerging contaminants over S/Fe codoped activated carbon fabricated by a mild one-step thermal transformation scheme

Enhanced stability of Cu/AC catalyst with modified hydrophobic layer for methanol oxidative carbonylation to dimethyl carbonate

Functionalized Activated Carbon for Competing Adsorption of Volatile Organic Compounds and Water

Unveiling the promotional mechanisms of N-doping on the adsorption behaviors of dioxins from sintering flue gas by coconut shell-derived hierarchical porous carbon

Loading mechanism and double-site reaction mechanism of Cu on activated carbon for enhanced oxidation of CO from flue gas

Co-production of spirosiloxane and biochar adsorbent from wheat straw by a low-cost and environment-friendly method

Experimental study and DFT calculation of the role of Cu loaded on activated carbon in desulfurization under dry and moist atmospheres

Introducing Molecular Sieve into Activated Carbon to Achieve High-Effective Adsorption for Ethylene Oxide

Comparison of perfluoroalkyl substance adsorption performance by inorganic and organic silicon modified activated carbon

Improving the performance of activated carbon towards dibenzothiophene adsorption by functionalization and sulfur-metal interactions

Comprehensive Study Of Pore Evolution, Mesostructural Stability, And Simultaneous Surface Functionalization Of Ordered Mesoporous Carbon (Fdu-15) By Wet Oxidation As A Promising Adsorbent

Adsorption of copper from water using TiO2-modified activated carbon derived from orange peels and date seeds: Response surface methodology optimization

Siloxane treatment by adsorption into porous materials