Abstract:Carbide-free nano-bainite steel holds significant potential for applications in mining as an ultra-high strength wear-resistant steel, but the wear mechanisms are not yet fully understood. This study aims to explore the effect of austempering temperature on microstructure, mechanical properties and wear resistance of carbide-free nano-bainitic steel. The relationship between the content and mechanical stability of retained austenite (RA) and mechanical properties was investigated to elucidate the mechanisms of pin-on-disc wear and impact wear. The results show that in the range of M s ∼300 °C, the phase transformation incubation period and completion time significantly increase with decreasing austempering temperature, which is mainly related to higher phase transformation driving force resulting from a larger subcooling degree and slow growth of carbon content in RA. Optimal strength and hardness of 2099 MPa and 615 HBW, respectively, are achieved after austempering at 210 °C for 83 h. Austempering at 270 °C for 11 h yields the best balance of strength and plasticity, with a strength-plasticity product of 28.8 GPa%. The micro-cutting mechanism of pin-on-disc wear leads to serious weight loss. The RA with poor mechanical stability accelerates the stress-induced martensite transformation, while internal stress support due to volume expansion reduces the penetration depth of abrasive particles. The weight loss in impact wear is primarily caused by shedding due to fatigue failure. With the increase of RA content and mechanical stability, the persistent stress-induced martensite transformation effectively hinders micro-crack propagation, thereby enhancing impact wear resistance.

A Study of Deformation Behavior and Stability of Retained Austenite in Carbide-Free Bainitic Steel During Nanoindentation Process

Strain-induced Refinement and Thermal Stability of a Nanocrystalline Steel Produced by Surface Mechanical Attritiontreatment

Nanomechanics of Retained Austenite in Medium-Carbon Low-Temperature Bainitic Steel: A Critical Analysis of a One-Step versus a Two-Step Treatment

Nano-indentation Investigation on the Mechanical Stability of Individual Austenite in High-Carbon Steel

Micro Plastic Deformation Behavior Of Carbide-Free Bainitic Steel During Tensile Deformation Process

Nanoindentation Investigation on the Mechanical Stability of Individual Austenite Grains in a Medium-Mn Transformation-Induced Plasticity Steel

Investigating the Difference in Mechanical Stability of Retained Austenite in Bainitic and Martensitic High-Carbon Bearing Steels using in situ Neutron Diffraction and Crystal Plasticity Modeling

In-situ Observation of Tensile Deformation and Retained Austenite Transformation Behaviors in Carbide-Free Bainitic Steel

Local Plastic Indentation Resistance of Retained Austenite in Bearing Steel

Insight into the impact of microstructure on crack initiation/propagation behavior in carbide-free bainitic steel during tensile deformation

Microstructure Evolution In A Low Carbon Nb-Ti Microalloyed Steel

Novel Method for Refinement of Retained Austenite in Micro/nano-Structured Bainitic Steels

Effect of Austempering Temperature on Microstructure Evolution, Mechanical Properties and Wear Resistance of Carbon-free Nano-bainite Steel

Study on Quasi-in-situ Tensile Deformation Behavior in Medium-Carbon Carbide-Free Bainitic Steel

Stress-induced Martensitic Transformation in Metastable Austenite Grains During Nanoindentation Investigation

Effect of Carbon Content in Retained Austenite on the Dynamic Tensile Behavior of Nanostructured Bainitic Steel

Effect of Nickel on Hardening Behavior and Mechanical Properties of Nanostructured Bainite-Austenite Steels

Study of Micro Deformation of Austenitic-Ferrite Duplex Stainless Steel by Nanoindentation Method

Notably Accelerated Nano-Bainite Transformation via Increasing Undissolved Carbides Content on GCr15Si1Mo Bearing Steel

Ultrahigh strength martensite-austenite dual-phase steels with ultrafine structure: The response to indentation experiments

Micromechanical Behavior of Transformation‐Induced Plasticity‐Assisted Annealed Martensitic Steel Using in Situ Neutron Diffraction