Abstract:The ribbed serpentine blade cooling system is a typical configuration in the modern gas turbine airfoil. In this study, experimental and the numerical efforts were carried out to investigate the local heat transfer and pressure drop distribution of a ribbed blade cooling system with different configurations in the turn region. A test rig containing a ribbed rectangular U-duct with a 180 deg round turn was built in Tsinghua University for this study. The transient liquid crystal method was applied to get the heat transfer distribution. Nine test cases with three turn configurations under three Reynolds numbers were carried out in the experiment. Pressure was measured along the duct in order to determine the influence of turning vane configurations on pressure drop. The test cases were also analyzed numerically based on Reynolds-averaged Navier-Stokes (RANS) with three different turbulence models: the k-ε model, the SST reattachment model, and the Omega Reynolds stress (ORS) turbulence model. Both the experimental and numerical results showed a significant influence of the turning vane configuration on the heat transfer and pressure drop in the convective cooling channel. Among the three configurations, the loss coefficient of turn in configuration 2 was lowest due to the introduction of turning vane. Even the ribs were added in the turn region of configuration 3, the loss coefficient and friction factor are reduced by 23% and 17.5%, respectively. Meanwhile, the heat transfer in baseline configuration is still the highest. As the introduction of turning vane, the heat transfer in the region after turn was reduced by 35%. In configuration 3, the heat transfer in the turn region was enhanced by 15% as the ribs installed in the turn region. In the before turn region, the pressure drop and heat transfer was not influenced by the turn configuration. All the turbulence models captured the trend of heat transfer and pressure drop distribution of three test sections correctly, but all provide overpredicted heat transfer results. Among the models, the ORS turbulence model provided the best prediction. While aiming at high heat transfer level and low pressure drop, it is suggested that a suitable turn configuration, especially with the turning vane and/or the ribs, is a promising way to meet the conflicted requirements of the heat transfer and pressure drop in the convective cooling system.

Numerical Investigations into the Effects of Turning Vanes on Heat Transfer and Flow of a 2-Pass Ribbed Internal Cooling Channel with a UShape Bend

Effect of Ribs on Heat Transfer and Pressure Drop in a U-Bend Channel With Double-Layer, Dome-Shaped Turning Vanes

Effects of Turning Vane on Flow Control and Heat Transfer in Ribbed Two-Pass Channel with Varied Rib Patterns

Effects of Novel Turning Vanes on Pressure Loss and Tip-Wall Heat Transfer in an Idealized U-bend Channel

Effects of varied bend turning vanes on flow control and heat transfer performance in a smooth two-pass channel

Numerical Study of the Influence of Rib Orientation on Heat Transfer Enhancement in Two-Pass Ribbed Rectangular Channel

Numerical Analysis and Experiments on Heat Transfer and Flow Structures in Rotating Three-Pass Serpentine Channels with Ribs, Guide Vanes and Trailing Bleed Holes

Effect of a Turning Vane on Heat Transfer in Rotating Multipass Rectangular Smooth Channel

Heat Transfer in Rotating Multi-Pass Rectangular Ribbed Channel with and Without a Turning Vane

Improving heat transfer performance in two-pass ribbed channel by the optimized secondary flow via bend shape modification

Numerical Calculations on Flow and Heat Transfer in Smooth and Ribbed Two-Pass Square Channels under Rotational Effects

Investigation on Heat Transfer Distribution of Rotating Two-Pass Smooth and Ribbed Channels under Aero-Engine Simulated Conditions

Effect of Turning Vane Configurations on Heat Transfer and Pressure Drop in a Ribbed Internal Cooling System

Numerical investigation on vane leading edge impingement cooling performance under influences of ribs established between adjacent jets

Experimental and Numerical Investigation of Turbulent Flow Heat Transfer in a Serpentine Channel with Multiple Short Ribbed Passes and Turning Vanes

Numerical Analysis of Heat Transfer Characteristics in Ribbed Two-Passed Channel with Varied Cross Section

Numerical Predictions on Heat Transfer and Flow Characteristics in a Straight Channel with Different Geometric Parameters Wavy Ribs

Heat Transfer Enhancement in Gas Turbine U-Shaped Channel with Rib Tabulators under Rotational Effect

Numerical Investigation on Flow and Cooling Characteristics of a Micro-Ribbed Vane Endwall

An Experimental Investigation of Heat Transfer Characteristics in a Steam-Cooled Square Channel with Rib Turbulators

Numerical Study on Flow and Heat Transfer in A Rectangular Channel with 45 Deg Rib Turbulators and Bleed Holes