Abstract:A new jet fuel surrogate was developed in this work by emulating real jet fuel properties including physical, gas phase chemical properties and threshold sooting index (TSI). An intelligent optimization methodology was proposed to calculate the species composition that inherently satisfies both the physical and chemical characteristics as well as sooting tendency. Eight properties were selected as the target properties for the jet fuel surrogate development, including liquid density, viscosity, surface tension, cetane number (CN), hydrogen carbon (H/C) ratio, molecular weight (MW), lower heating value (LHV) and TSI. As a result, the CN, H/C ratio, LHV, TSI and density of the new jet fuel surrogate are reproduced excellently with very little deviations within 3%. The averaged deviation of viscosity is −6.318% and the deviations of MW is 9.776%. As the highest deviation among all properties, the averaged deviation of surface tension is 11.76%. Based on the newly developed jet fuel surrogate, a skeletal jet fuel surrogate mechanism with 5 components including decalin, n-dodecane, iso-cetane, iso-octane and toluene was developed. The skeletal jet fuel surrogate mechanism was significantly compacted into 74 species and 189 reactions by describing the chemistries for the oxidation of large molecules C4–Cn and small H2/CO/C1 molecules respectively, which makes it practical to be used for 3-D engine combustion simulations. The validations of ignition delay times present reasonable agreement between experiment and predictions over a wide range of equivalence ratios (0.5–2.0) and pressures (8–30 atm), except for a shift of negative temperature coefficient (NTC) region towards higher temperatures at Φ = 1.5, 20 atm: in the simulation the NTC region is from 830 K to 950 K while in the experiment the NTC region is from 740 K to 890 K. The predicted species concentrations can reproduce the trend of the experimental data, especially for O2, CO and CO2. The simulated laminar flame speed at 400 K and 470 K are with absolute averaged deviations of 3.5% and 4.06% respectively. The constant volume spray and combustion validations are reasonably good. In the engine combustion validations, a multistep soot model was embedded into the new jet fuel surrogate mechanism. The predicted in-cylinder pressure can reproduce the experimental data, expect for small deviations after the peak pressure (the averaged deviation is around 6.2% after the peak pressure). The embedded soot model can well reproduce the trend of the experimental data. It can be concluded that this new jet fuel surrogate mechanism is compact and robust for the utilization in diesel engine combustion simulation.

An Experimental Study on the Laminar Burning Velocities of RP-3 Kerosene and Its Surrogate Fuel at Elevated Pressures and Temperatures

Laminar Burning Characteristics of Upgraded Biomass Pyrolysis Fuel Derived from Rice Husk at Elevated Pressures and Temperatures

Analyses of Surrogate Models for Calculating Thermophysical Properties of Aviation Kerosene RP-3 at Supercritical Pressures

RP-3 Aviation Kerosene Surrogate Fuel and the Chemical Reaction Kinetic Model

Development and validation of a detailed kinetic model for RP-3 aviation fuel based on a surrogate formulated by emulating macroscopic properties and microscopic structure

Numerical Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Consideration of Fuel Pyrolysis and Surface Coking at Supercritical Pressures

The influence of methyl butyrate and n-butanol on the laminar burning characteristics of RP-3: An experimental and kinetic modeling study

An experimental and modeling study of oxidation of real RP-3 aviation kerosene

Molecular dynamics simulation of thermophysical properties of binary RP-3 surrogate fuel mixtures containing trimethylbenzene, n-decane, and n-dodecane

Asymmetric Heating and Buoyancy Effects on Heat Transfer of Hydrocarbon Fuel in a Horizontal Square Channel at Supercritical Pressures

Modeling and Simulation of Supercritical-Pressure Turbulent Heat Transfer of Aviation Kerosene with Detailed Pyrolytic Chemical Reactions

Soot and PAH Formation in Laminar Diffusion Flames of RP-3 Jet Kerosene and Its Surrogates at Preheat Temperature

Comparative Research on Laminar Flame Propagation for Four C8 Fuels

An experimental study on the instability of RP-3 aviation kerosene/air premixed flame

Development of a New Jet Fuel Surrogate and Its Associated Reaction Mechanism Coupled with a Multistep Soot Model for Diesel Engine Combustion

C4+ Surrogate Models for Thermophysical Properties of Aviation Kerosene RP-3 at Supercritical Pressures

Experimental and Numerical Study on the Laminar Flame Characteristics for PODE3 and PODE3/iso-octane Blends under Elevated and Sub-Ambient Initial Pressures

Study on the laminar burning velocity of ethanol/RP-3 aviation kerosene premixed flame

Comparison of RP-3 Pyrolysis Reactions Between Surrogates and 45-Component Model by ReaxFF Molecular Dynamics Simulations

Effect of Pressure on Burning and Soot Characteristics of RP-3 Kerosene Droplets under Sub-Atmospheric Pressure

Model Validation and Parametric Study of Fluid Flows and Heat Transfer of Aviation Kerosene with Endothermic Pyrolysis at Supercritical Pressure