Abstract:Ambitious electrification roadmaps for the automotive industry have prompted a revolution in winding technology for traction motors in electric vehicles (EV). Hairpin windings with reduced power losses and improved coolability are overtaking the market compared with stranded windings. Currently, most hairpin winding solutions use state-of-the-art end winding cooling strategies. This, however, still cannot bridge the gap for high performance requirements, so supplementary in-slot cooling is needed to make the next step change in achieving high power density. This paper will investigate direct in-slot cooling of hairpin windings with a focus on cooling channel arrangement. A novel analytical parametric Lumped Parameter Thermal Network modelling methodology is developed to choose the thermally optimal in-slot cooling channel radial position for a 150kW high speed traction motor. Two operating points (corner and peak speed) on the peak torque-speed curve are studied to investigate how machine losses influence the choice of the optimal cooling channel position. Changing loss distributions showed an optimal middle channel position for the corner speed and shift towards the airgap at peak speed. A typical slot-opening channel position was shown to reduce hotspot temperatures by 23 K compared with a no-in-slot cooling benchmark, for the most thermally challenging operating point. A further 8 K reduction is achieved, compared to the benchmark, for the most thermally challenging operating condition, when a central cooling channel position is chosen. The novelty of this paper is the multiphysics electromagnetic and thermal modelling methodology integration which the trade-off between losses and temperatures, as impacted by a changing channel position, capture. An FEA model was built to validate the LPTN results for the benchmark case; the temperature rise between the hotspot slot peak and the oil inlet temperature, was predicted within 5%.

Fast Sizing Tool and Optimization Technique for Concentrated Wound Slotless Outer Rotor Motor for Evtol Application

Design and Fem Analysis of A High Efficiency Axial-Flux Brushless Dc Motor for Flywheel System

Design Consideration of Fractional Slot Concentrated Winding Interior Permanent Magnet Synchronous Motor for EV and HEV Applications

Research on Yokeless Double-Sided Multi-Tooth Flux-Switching Linear Motor

Design and Analysis of Outer Rotor Permanent-Magnet Vernier Machines with Overhang Structure for In-Wheel Direct-Drive Application

Carbon Emission Comparison of Slotted and Slotless Motors for Evtol Application

Analysis of a Novel Linear Doubly Salient Slot Permanent Magnet Motor

Design and Comparison of Two Axial Flux Motors for Electric Aircraft

Comparative Study of Yokeless Stator Axial-Flux PM Machines having Fractional Slot Concentrated and Integral Slot Distributed Windings for Electric Vehicle Traction Applications

Design Optimization of Four-Layer Fraction Slot Concentrated Winding Spoke-Type Interior Permanent Magnetic Machine for Range Extender

Design of Helical Winding for Slotless Partially Superconducting Electric Machines for Aircraft Propulsion

Multi-three-phase FSCW High-speed High-power-dense Inset Bread-loaf PMSM for the Electric VTOL Application

Design and Optimization of a Slotless High-speed Permanent-Magnet Synchronous Motor with Non-magnetic Fillers in Stator

A Novel Axial-Flux Permanent Magnet Vernier Machine with H-Core Stator Modules and Toroidal Windings for Electric Aircraft Propulsion System

A Novel Double-Sided Offset Stator Axial-Flux Permanent Magnet Motor for Electric Vehicles

Optimization of a 12-Slot/10-Pole, Asymmetrical, Six-Phase IPM Considering Healthy and Open-Phase Fault Post Operation in EV Applications

In-Slot Oil Cooling Arrangement of Hairpin Windings for High Power Density EV Traction Motors

Optimized rotor structural design methodology for high-speed electrical machines based on mechanical characteristics

Modeling and Simulation of a Novel Low-Speed High-Torque Permanent Magnet Synchronous Motor with Asymmetric Stator Slots

Comparative Study of 6-Slot/2-pole High-Speed Permanent Magnet Motors with Different Winding Configurations

Design and Analysis of a New Outer‐rotor Permanent‐magnet Flux‐switching Machine for Electric Vehicle Propulsion