Abstract:Photoelectrochemical water splitting using semiconductor materials is one of the most promising methods for converting solar energy into chemical energy. Among the commonly used semiconductors, p-type CuBi2O4 is considered one of the most suitable photocathode materials and can allow a theoretical photocurrent density of about 20 mA center dot cm(-2) for photoelectrochemical water splitting. However, due to severe charge carrier recombination, the obtained photocurrent density is much lower than the theoretical value. Highly efficient photoelectrochemical performance relies on fast charge carrier separation and transport, and prompt reaction kinetics. In this study, we report the development of a polyoxometalate-modified CuBi2O4/Mg- CuBi2O4 homojunction photocathode to improve both the bulk and interfacial charge carrier transport in the photocathode. For the bulk of the photocathode, the built-in electric field originating from the CuBi2O4/Mg-CuBi2O4 homojunction promotes the migration of photo-excited electrons on the conduction band from pure CuBi2O4 to Mg-doped CuBi2O4. Additionally, the electric field facilitates the transfer of holes from the valence band of Mg-doped CuBi2O4 to pure CuBi2O4. This directional transfer of both photo-excited electrons and holes plays a significant role in promoting separation and suppressing the recombination of the charge carriers. On the surface of the photocathode, the reduced polyoxometalate co-catalyst Ag6[P2W18O62] (AgP2W18) was used as a proton sponge to accelerate surface reaction kinetics and suppress carrier recombination. These synergistic effects improved the photo-generated charge carrier transfer and reaction kinetics. As a result, the novel photocathode displayed excellent photoelectrochemical properties, and the photocurrent density was observed to be-0.64 mA center dot cm(-2) at 0.3 V vs. RHE, which is better than that of-0.39 mA center dot cm(-2) for a pure photocathode. Furthermore, the novel photocathode had an applied bias photon-to-current efficiency (ABPE) higher than 0.19% at 0.3 V vs. RHE. In contrast, the pure photocathode had an ABPE of similar to 0.12% under the same conditions. Additionally, when H2O2 was used as an electron scavenger, the photocurrent density was-3 mA center dot cm(-2) at 0.3 V vs. RHE, which is an improvement of approximately 1.5 times compared to the pure photocathode. Furthermore, the charge separation and charge injection efficiency of the novel photocathode were significantly improved compared with the pure photocathode. The experimental results conclusively indicate that the formation of the CuBi2O4/Mg-CuBi2O4 homojunction and AgP2W18 modification played a significant role in the improved performance of the CuBi2O4 photocathode. The performance of the novel photocathode was comparable with the results reported in previous studies, demonstrating its promising potential in real applications.

Plasma Ag-loaded Bandgap Variational Zn1-xMgxO-enhanced Charge Separation for Photoelectrochemical Water Oxidation of CuWO4 Photoanodes

Integration of a Cu2O/ZnO heterojunction and Ag@SiO2 into a photoanode for enhanced solar water oxidation

Design and In Situ Growth of Cu 2 O‐Blended Heterojunction Directed by Energy‐Band Engineering: Toward High Photoelectrochemical Performance

Synthesis of a Cu2O/Carbon Film/NiCoB‐Grpahene Oxide Heterostructure As Photocathode for Photoelectrochemical Water Splitting

A Universal Strategy Boosting Photoelectrochemical Water Oxidation by Utilizing MXene Nanosheets As Hole Transfer Mediators

Exploring the photoelectrochemical process through surface states of plasmonic Ag-loaded NiFe-LDH-modified CuWO 4 photoanode

Integrating transition metal phosphide catalysts on WO3 photoanodes enabling robust photoelectrocatalytic water oxidation

Improved Photoelectrochemical Performance by Polyoxometalate-Modified CuBi2O4/Mg-CuBi2O4 Homojunction Photocathode

Tuning the Carrier Transfer Behavior of Coaxial ZnO/ZnS/ZnIn2 S4 Nanorods with a Coherent Lattice Heterojunction Structure for Photoelectrochemical Water Oxidation

Synergistic improvement of charge separation and injection on CuPc modified BiVO 4 for efficient solar water oxidation

Oxygen Vacancy-Enhanced Photoelectrochemical Water Splitting of WO 3 /NiFe-Layered Double Hydroxide Photoanodes

Cu ions intercalated GO/Cu 2 O photocathode-enabled promotion on charge separation and transfer for efficient photoelectrochemical water splitting

Oxygen Vacancy-Enhanced Photoelectrochemical Water Splitting of WO3/NiFe-Layered Double Hydroxide Photoanodes.

Incorporation of Sulfate Anions and Sulfur Vacancies in ZnIn 2 S 4 Photoanode for Enhanced Photoelectrochemical Water Splitting

High-Voltage Etching-Induced Terrace-like WO 3 Photoanode for Efficient Photoelectrochemical Water Splitting

Design of Sandwich-Structured ZnO/ZnS/Au Photoanode for Enhanced Efficiency of Photoelectrochemical Wate Splitting

ZnO photoelectrode simultaneously modified with Cu2O and Co-Pi based on broader light absorption and efficiently photogenerated carrier separation

Gradient surficial forward Ni and interior reversed Mo-doped CuWO4 films for enhanced photoelectrochemical water splitting

Engineering MoOx /mxene Hole Transfer Layers for Unexpected Boosting of Photoelectrochemical Water Oxidation.

Enhanced bulk and interfacial charge transfer in Fe:VOPO4 modified Mo:BiVO4 photoanodes for photoelectrochemical water splitting

Cu2O/CuO heterojunction formed by thermal oxidation and decorated with Pt co-catalyst as an efficient photocathode for photoelectrochemical water splitting