Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. In the present work, the creep strength-enhanced ferritic martensitic P92 steel was welded with 304L austenitic stainless steel. The dissimilar joining of these two different grades of material was performed by using tungsten inert gas welding process. The nickel-based ERNiCr-3 welding consumable was used. The influence of post-weld heat treatment (760 °C, 2h), called as tempering, was also investigated. The secondary electron and optical image confirmed that ERNiCr-3 weld metal is accompanied by an equiaxed austenitic microstructure with Ni weight percentage of 68.29%. The energy-dispersive X-ray spectroscopy and electron probe microanalyzer results of the weld fusion zone revealed the Nb, Cr, and Ti segregation in the inter-dendritic region. The elemental mapping of the carbon-depleted zone, and the interface was performed using an electron probe microanalyzer, which revealed the diffusion of Ni, Cr, and Fe across the interface of P92 steel and ERNiCr-3 filler weld. The tensile test result indicated that part of the dissimilar weld joints (DWJs) with relatively weak ultimate tensile strength was ERNiCr-3 weld metal. The ultimate tensile strength value of the DWJs was observed as 610 MPa and 580 MPa in the as-weld and post-weld heat treatment situations, respectively. The Charpy V-notch impact energy of the ERNiCr-3 weld fusion zone was achieved as 135 ± 2 J and 140 ± 2 J in as-weld and post-weld heat treatment situations, respectively. The low impact toughness of the ERNiCr-3 weld metal was attributed to the presence of niobium carbide (NbC) and titanium carbide (TiC) particles. The peak longitudinal residual stress of 490 MPa and transverse residual stress of 442 MPa were noted in the ERNiCr-3 weld fusion zone at a depth of 3 mm from the top surface. The tempering heat treatment exhibited a significant drop in the residual stresses value for the weld fusion zone and heat affected zone (HAZ).

Investigation of C276 alloy and 316L SS TIG welded joints with ERNiCrMo-4 and ER304 welding wires

Investigation of Microstructures and Mechanical Properties of T92 Martensitic Steel/Super304 Austenitic Steel Weld Joints Made with Three Welding Consumables

Microstructural characteristics and mechanical properties of underwater wet flux-cored wire welded 316L stainless steel joints

On the investigation of microstructure and mechanical properties of the AlCoCrFeNi 2.1 /316 L dissimilar spot-welded joint

Microstructure and mechanical properties of electron beam welded joints of GH3128 and CoCrFeNi high-entropy alloy

On the Investigation of Microstructure and Mechanical Properties of the AlCoCrFeNi2.1/316 L Dissimilar Spot-Welded Joint

Investigation on Microstructure and Properties of Dissimilar Joint Between SA553 and SUS304 Made by Laser Welding with Filler Wire

Microstructure and Mechanical Properties of Dissimilar TC4 Titanium Alloy/304 Stainless Steel Joint Using Copper Filler Wire

Enhancing microstructural and mechanical characteristics of laser welded NiTi SMA/304 SS lap joints with medium and high entropy alloy fillers

Welding Dissimilar Alloys of CoCrFeMnNi High-Entropy Alloy and 304 Stainless Steel Using Gas Tungsten Arc Welding

Study on Explosive Welding for Manufacturing Meshing Bonding Interface of CuCrZr to 316L Stainless Steel

Microstructure and mechanical properties of gas metal arc welded CoCrFeMnNi joints using a 308 stainless steel filler metal

Residual stress analysis, microstructural characterization, and mechanical properties of tungsten inert gas-welded P92/AISI 304L dissimilar steel joints

Study on the microstructure optimization and mechanical properties of dissimilar TC4-304L arc-brazing joints

Microstructure and Mechanical Properties of Welded Joints of Cr18Ni30Mo2Al3Nb Alloy

Formation, Microstructure, and Properties of Dissimilar Welded Joint between CrMnFeCoNi and Fe

Microstructure and Mechanical Properties of Fe-36Ni and 304L Dissimilar Alloy Lap Joints by Pulsed Gas Tungsten Arc Welding

The influence of different alloyed welding materials on the microstructure and mechanical properties of welded interface in TiC cermet MIG welding bonds

Microstructure, Residual Strain and Stress Corrosion Cracking Behavior in 316L Heat-Affected Zone

Microstructure and Mechanical Properties of Dissimilar Welds Between 16mn and 304L in Underwater Wet Welding

Microstructure and Mechanical Properties of Fiber Laser Welded Joints of CoCrFeNiCu High-Entropy Alloy and 304 Stainless Steel