Abstract:In recent years, the Moon, as the only satellite of the Earth, has once again become the primary destination for exploration by countries around the world. However, considering the limited carrying capacity and high cost of extraterrestrial space construction, additive manufacturing (AM) technology, such as the photopolymerization method, for in-situ resource utilization (ISRU) lunar regolith has attracted the favor of researchers for building lunar research bases. Still, the photopolymerization of lunar regolith simulant (LRS) systems has been greatly limited by the imbalance of high solid content and low viscosity of the prepared slurries. To address this challenge, previous studies employed a silane coupling agent (KH-570) or stearic acid (SA) to modify the surface of the powder, but the process is complicated and unsuitable for use in lunar microgravity environments. In this research, based on the principle of emulsification of two different solutions, by introducing a certain proportion of aqueous solution, under the action of disperbyk-111, the interface between water and resin forms a directional molecular layer to reduce surface tension. According to the Gibbs adsorption formula, the decrease in surface tension will increase the adsorption amount of the surface layer per unit area, which means that the closer the molecular arrangement is, the more stable the emulsion is. The macroscopic phenomenon reduces the viscosity while ensuring the retention properties of the material, which better solves the problem that high solid content LRS paste is difficult to achieve low viscosity. The comparative analysis of the viscosity shows that adding an aqueous solution has achieved the expected result. Herein, we developed LRS paste with 62 vol% (i.e., 80 wt%) solid content for the use of stereolithography (SL) vat photopolymerization (VP) and completed the printing successfully. The experimental results further suggested that the sample layer thickness of 50 µm and the placement angle of 0° were the most suitable for successful printing. The average flexural and compressive strength reached 132.21 MPa and 444.23 MPa, surpassing previous results. In addition, the phenomenon of interlayer bonding at different placement angles observed by scanning electron microscope (SEM) was explained by the secondary extrusion force per unit area. Finally, we also realized the printing of integral one-piece movable parts using LRS materials, achieving high precision and superior performance, which makes it possible to print high-strength structures on the Moon in the future.

Vat Photopolymerization of Low-Titanium Lunar Regolith Simulant for Optimal Mechanical Performance

Optimized sintering strategy for lunar regolith simulant particles bound via vat photopolymerization

Additive manufacturing of high solid content lunar regolith simulant paste based on vat photopolymerization and the effect of water addition on paste retention properties

Development of lunar regolith-based composite for in-situ 3D printing via high-pressure extrusion system

Thermal Weathering of 3D-Printed Lunar Regolith Simulant Composites

Additive Manufacturing by Laser Powder Bed Fusion and Thermal Post-Treatment of the Lunar-Regolith-based Glass-Ceramics for In-Situ Resource Utilization

Effect of sintering temperature on microstructure and mechanical properties of molded Martian and Lunar regolith

Additive manufacturing of hydrogel-based lunar regolith pastes: A pathway toward in-situ resource utilization and in-space manufacturing

3D Printing and Solvent Dissolution Recycling of Polylactide–Lunar Regolith Composites by Material Extrusion Approach

Matrix transformation of lunar regolith and its use as a feedstock for additive manufacturing

Selective laser melting of partially amorphous regolith analog for ISRU lunar applications

Effect of TiO2 on the Microstructure and Flexural Strength of Lunar Regolith Simulant

In-situ Solidification of Alkali-Activated Lunar Regolith: Insights into the Chemical and Physical Origins

Preparation, Characterization and Designing of Porous Ti–6Al–4V Through Metal Injection Molding Without Space Holder

Lunar regolith - AlSi10Mg composite fabricated by selective laser melting

Melting properties of lunar regolith simulant for in-situ construction

Preparation and Characterization of High-Strength Geopolymer Based on BH-1 Lunar Soil Simulant with Low Alkali Content

Boosting the Mechanical and Thermal Properties of CUG-1A Lunar Regolith Simulant by Spark Plasma Sintering

In-situ Visualization of Powder Wrapping Behavior in Millimeter-Scale-beam Lunar Regolith Powder Bed Fusion

Compaction Self-Assembly of Ultralow-Binder-Content Thermoplastic Composites Based on Lunar Soil Simulant

Dynamic mechanical properties of Alumina prepared by vat photopolymerization based on high solid loading slurry