Abstract:The refractive index of silicon-based waveguide materials is highly sensitive to temperature and stress, and the effective refractive index of the waveguide varies with temperature changes. Thus, it is critical to reduce the temperature dependence of Arrayed Waveguide Grating (AWG) devices and to precisely control the center wavelength of AWGs. In this study, the thermoelectric cooler (TEC) was designed and fabricated to control the temperature of the thermal AWG chip, which did not require any material replacement or reprocessing of the AWG chip. Different magnitudes and polarities of voltage are applied to the TEC to regulate its operational state (heating or cooling). A multiphysics simulation model of a thermal AWG device is established and validated through transient and steady-state experiments. This study investigated the influence of different conditions (input voltage, environmental temperature) on the temperature and maximum stress of the AWG chip. A conformal TEC was designed and its performance was compared with that of the square TEC. The energy consumption of the conformal TEC was also tested and analyzed. The results show that in a 25 °C ambient environment, the TEC can control the temperature of the AWG chip in the range of 1.5–78.3 °C, significantly expanding the current operational temperature range of 65.0–85.0 °C when using Positive Temperature Coefficient (PTC) heaters. Under the same conditions, when using the conformal TEC as the temperature control device, the temperature gradient on the AWG chip is reduced by 1.37 °C during cooling and 2.80 °C during heating. The maximum stress value in the core layer is always lower, with a maximum reduction of 3.61 MPa. TEC can set the ideal operating temperature of the AWG chip according to the actual operating environment of the product, which reduces the energy consumption of TEC. A comparison is made between the average power consumption of the conformal TEC and the PTC heater under two operating conditions: a 25 °C constant-temperature environment and a natural environment. The average power consumption can be reduced by up to 97.87 % and 93.02 %, respectively. This study holds significant guidance for solving the temperature dependence problem of AWG devices and the application of thermoelectric coolers in the field of optical communication.

A Combined Solution of Thermoelectric Coolers and Microchannels for Multi-Chip Heat Dissipation with Precise Temperature Uniformity Control

Advancing Cryogenic Electronic Cooling: A Case Study on Embedded Manifold Microchannels in Micromachined Joule-Thomson Coolers

Experimental Study and Taguchi Analysis on LED Cooling by Thermoelectric Cooler Integrated with Microchannel Heat Sink

Case-embedded cooling for high heat flux microwave multi-chip array

Investigation on the Linear Cooling Method of Microfluidic Chip Based on Thermoelectric Cooler

A Highly Efficient Integrated Silicon-Microchannel Cooler for Multi-Module Electronic Microsystems: Model Design, Optimization, and Performance Validation

Active Thermal Management of Hotspot under Thermal Shock Based on Micro-Thermoelectric Cooer and Bi-Objective Optimization

Thermal Control in 3D Liquid Cooled Processors Via Hotspot Separation and Thermoelectric Cooling

Ultra-high Efficient Integrated Microchannel Cooling for Multi-unit Microsystems

An experimental investigation and multiphysics simulation of thermoelectric temperature controller for AWG chips

Embedded microfluidic cooling with compact double H type manifold microchannels for large-area high-power chips

A Bi-Layer Compact Thermal Model for Uniform Chip Temperature Control with Non-Uniform Heat Sources by Genetic-Algorithm Optimized Microchannel Cooling

Integrated Manifold Microchannels and Near-Junction Cooling for Enhanced Thermal Management in 3D Heterogeneous Packaging Technology

Numerical Study on Hybrid Discontinuous Microchannel Heat Sink Combining Manifold with Pin Fins (DMC-MPF) for High Power Electronic Device

Thermoelectric Coolers for Hotspot Thermal Management of 3D Stacked Chips

Electrically driven chip cooling device using hybrid coolants of liquid metal and aqueous solution

Effective Thermal Control Techniques for Liquid-Cooled 3D Multi-Core Processors

An Effective Method of Evaluating the Device-Level Thermophysical Properties and Performance of Micro-Thermoelectric Coolers

Thermoelectric active cooling for transient hot spots in microprocessors

Experimental Study of an Aluminum Based Three-Dimensional Thermosyphon Heat Sink with Microscale Enhancement Structure

Efficient on-chip hotspot removal combined solution of thermoelectric cooler and mini-channel heat sink