Intense removal of Ni (II) chelated by EDTA from wastewater via Fe3+ replacement–chelating precipitation
Sai Li,Tong Yue,Wei Sun,Chenyang Zhang,Jianyong He,Mingjun Han,Hongliang Zhang,Heng Yu,Wenyuan Li
DOI: https://doi.org/10.1016/j.psep.2022.01.080
IF: 7.8
2022-03-01
Process Safety and Environmental Protection
Abstract:Efficient removal of Ni (Ⅱ) chelated by ethylenediaminetetraacetic acid (EDTA) from wastewater remains an important but challenging environmental problem. Therefore, a novel strategy of Fe3+ replacement–chelating precipitation was proposed to remove Ni (Ⅱ) chelated by EDTA from simulated Ni-EDTA wastewater and real electroless nickel plating wastewater. The strategy was proved to be thermodynamically feasible by DFT calculation. Regardless of the simulated Ni-EDTA wastewater or the real electroless nickel plating wastewater, the residual nickel in the wastewater was less than 0.1 mg/L that satisfied the discharge standard after being treated under optimal conditions using this strategy. Moreover, the strong acidity and Fe3+ could increase the proportion of free Ni2+ in Ni-EDTA wastewater, thereby enhancing the Ni removal efficiency. Additionally, the total amount of EDTA in wastewater was basically unchanged, since the structure of EDTA was not destroyed by this strategy, while its chemical form changed from Ni-EDTA complex to Fe3+-EDTA complex. Furthermore, the mechanism was systematically studied by electronic structure analysis, solution chemistry, UV-Vis spectral, FT-IR spectral and X-ray photoelectron spectroscopy. At last, this strategy is a promising approach and it can provide a reference for the treatment of other similar heavy metal wastewater.Download : Download high-res image (149KB)Download : Download full-size imageTo solve the problem of calibrating the radius of a ball indenter in a hardness tester, a laser confocal radius measurement and calibration method for the ball indenter is proposed without separating the ball from the body of the indenter. The laser confocal radius measurement and calibration method uses the maximum of the confocal axial intensity curve to precisely identify the cat's eye and confocal position of the test ball indenter. The distance between these two positions is then measured to achieve high-precision radius measurement. The theoretical analyses and experimental results indicate that the radius measurement uncertainty of the ball indenter with a diameter of 1.5875 mm is within 0.12 μm.Phenylarsonics are present as additives in animal feed in some countries. As only a small fraction of these additives is metabolized in animals, they mostly end up in the environment. A comprehensive investigation of the fate of these additives is crucial for evaluating their risks. This review aims to provide a clear understanding of the transformation and reactive mechanism of phenylarsonics in vivo and in vitro and to evaluate their fate and associated risks. Degradation of phenylarsonics releases toxic As species [mainly as inorganic arsenic (iAs)]. Trivalent phenylarsonics are the metabolites or biotic degradation intermediates of phenylarsonics. The cleavage of As groups from trivalent phenylarsonics catalyzed by C-As lyase or other unknown pathways generates arsenite [As(III)]. As(III) can be further oxidized to arsenate [As(V)] and methylated to methyl-arsenic species. The half-lives associated with abiotic degradation of phenylarsonics ranged from a few minutes to tens of hours, while those associated with biotic degradation ranged from several days to hundreds of days. Abiotic degradation resulted in a higher yield of iAs than biotic degradation. The use of phenylarsonics led to elevated totbn al As and iAs levels in animal products and environmental matrices, resulting in As exposure risk to humans. The oxidation of phenylarsonics to As(V) facilitated the sorptive removal of As, which provides a general approach for treating these compounds. This review provides solid evidence that the use of phenylarsonics has adverse effects on both human health and environmental safety, and therefore, supports their withdrawal from the global market.The tremendous demand of lactic acid (LaA) in widespread applications has impelled the development of chemical strategies for LaA production. We developed dealuminzated ZSM-5 loaded erbium catalyst, which exhibited outstanding activity. As high as >96% of LaA yield was obtained using triose as raw material over 15-Er/deAl-ZSM-5 (2) catalyst. When xylose-glucose mixture (C-molar ratio, 1:1) was employed, the simultaneous conversion of xylose and glucose selectively to LaA with ∼69.1 C-mol% yield could be achieved. The characterization of catalyst revealed that the pretreatment by HNO3 successfully removed partial Al in the extra-framework of ZSM-5, leading to enlarged surface areas and promoted dispersion of Er species, as well as strengthened weak interacti -Abstract Truncated-
engineering, environmental, chemical