Abstract:High-performance broadband ultrasound transducers provide superior imaging quality in biomedical ultrasound imaging. However, a matching design that perfectly transmits the acoustic energy between the active piezoelectric element and the target medium over the operating spectrum is still lacking. In this work, an anisotropic gradient acoustic impedance composite material as the matching layer of an ultrasonic transducer was designed and fabricated; it is a non-uniform material with the continuous decline of acoustic impedance along the direction of ultrasonic propagation in a sub-wavelength range. This material provides a broadband window for ultrasonic propagation in a wide frequency range and achieves almost perfect sound energy transfer efficiency from the piezoelectric material to the target medium. Nano tungsten particles and epoxy resin were selected as filling and basic materials, respectively. Along the direction of ultrasonic propagation, the proportion of tungsten powder was carefully controlled to decrease gradually, following the natural exponential form in a very narrow thickness range. Using this new material as a matching layer with high-performance single crystals, the -6 dB bandwidth of the PMN-PT ultrasonic transducer could reach over 170%, and the insertion loss was only -20.3 dB. The transducer achieved a temporal signal close to a single wavelength, thus there is the potential to dramatically improve the resolution and imaging quality of the biomedical ultrasound imaging system.

Ultrabroad-bandwidth ultrasonic transducer based on Sm-doped PMN-PT ceramic/epoxy 1–3 composite

Ultrabroad-bandwidth ultrasonic transducer based on Sm-doped PMN-PT ceramic/epoxy 1-3 composite

High Frequency PMN-PT 1-3 Composite Transducer for Ultrasonic Imaging Application

Miniature Ultrasound Transducer Incorporating Sm-PMN-PT 1-3 Composite

Wide-bandwidth Immersion Ultrasound Transducer Made of Mn:PIMNT Single Crystal/epoxy 1-3 Composite

Fabrication of Angle Beam Two-Element Ultrasonic Transducers with PMN–PT Single Crystal and PMN–PT/epoxy 1–3 Composite for NDE Applications

Fabrication of PMN-PT/Epoxy 2–2 Composite Ultrasonic Transducers and Analysis Based on Equivalent Circuit Model

High Frequency Ultrasound Transducer Based on Sm-Doped Pb(Mg1/3Nb2/3)O3-0.28PbTiO3 Ceramic for Intravascular Ultrasound Imaging

High Frequency Ultrasound Transducer Based on Sm-Doped Pb(Mg 1/3 Nb 2/3 )O 3 -0.28PbTiO 3 Ceramic for Intravascular Ultrasound Imaging

PIN-PMN-PT Single-Crystal-Based 1–3 Piezoelectric Composites for Ultrasonic Transducer Applications

Broadband Ultrasonic Transducer Based on Textured Lead-Free NKN-based Piezoceramics

Fabrication and Properties of the Thickness Mode Ultrasonic Transducer Based on 0.15Pb(mg1/3nb2/3)o3-0.38Pbhfo3-0.47pbtio3 Piezoelectric Ceramics

Electrical Characteristics of High-Performance Ultrasonic Transducer for Non-Destructive Testing

Enhancement of Ultrasonic Transducer Bandwidth by Acoustic Impedance Gradient Matching Layer

PZT/epoxy Multi-Composites for Ultrasonic Transducer Applications

Design of Piezoelectric Ultrasonic Transducer Based on Doped PDMS

High-frequency PIN–PMN–PT Single Crystal Ultrasonic Transducer for Imaging Applications

Research and Fabrication of High-Frequency Broadband and Omnidirectional Transmitting Transducer

Multiple matching scheme for broadband 0.72Pb(Mg(13)Nb(23))O(3)-0.28PbTiO(3) single crystal phased-array transducer.

Application of PMN-PT Piezoelectric Monocrystal in Wideband Transducer with Composite Rod Matching Layer.

0.36Bisco 3 –0.64pbtio 3 /epoxy 1–3 Composite for Ultrasonic Transducer Applications