Abstract:The quasicrystal (QC)-abrasive wear produces a flattened surface compared with traditional abrasives when used to polish metals, opening up new application fields for QC in particle form, but the influence range and extent of QC-abrasive on metal surface are not clear. In this work, the single particle grinding model was used for finite element simulation to qualitatively characterize the effect of QC-abrasive on the subsurface of stainless steel, which was ground by diamond, Al, Q, and QC single particle abrasive, respectively. The effects of three kinds of abrasives on the equivalent stress and strain of stainless steel surface were compared. Combined with the measurement of the gradient hardness of stainless steel subsurface, the Mott-Schottky plots and potentiodynamic polarization curve were given, analyzing the corrosion resistance mechanism of passivation film formed on the surface of stainless steel pretreated with QC-abrasive. The results show that the equivalent plastic strain of the stainless steel surface is the highest, up to 73%, when it is ground by QC single particle abrasive repeatedly for six times, which is consistent with the smearing coefficient measured in the experiment. The smearing-dominating on the surface of stainless steel treated with QC-abrasive is strengthened with time increased, but diamond and Al2O3 abrasives are improved cutting-dominating with time increased. At the same time, a large number of plastic deformation areas accumulated a higher stress, longitudinal sub-surface of stainless steel treated by QC-abrasive show a higher gradient distribution of equivalent stress. The simulation results are consistent with the changes of hardness of stainless steel at different depths measured in the experiment. The hardness of QC-abrasive treated stainless steel maintains the highest value at 200, 400 and 1800 nm to the surface, respectively. It is manifested as the gradient law of gradual decrease from the surface layer to the interior of the matrix. The Mott-Schottky plots with the minimum carrier concentration prove a large amount of plasticity accumulated on the subsurface of stainless steel treated via QC-abrasive, providing the preferred channel for the passivation element to bond with oxygen when the passivation film is formed on the surface. It can promote the formation of a complete passivation film on surface. The minimum passivation current density with 0.73x10(-6) A/cm(2) of potentiodynamic polarization curve indicates that QC-abrasive pretreated the surface of stainless steel is easier to be passivated. It is also less likely to be punctured to form pitting corrosion due to the relatively high breakdown potential.

Dry Passivation of Austenitic SUS 301L Stainless Steel Against Pitting Corrosion in Marine Atmospheric Environment

Passivation-induced physicochemical alterations of the native surface oxide film on 316L austenitic stainless steel

Microscopic origin of high corrosion resistance in 316L stainless steel by acidic passivation treatments

Effects of nitric acid passivation on the corrosion behavior of ZG06Cr13Ni4Mo stainless steel in simulated marine atmosphere

Chloride-induced alterations of the passive film on 316L stainless steel and blocking effect of pre-passivation

Improvement of Corrosion Resistance and Electrical Conductivity of Stainless Steel 316L Bipolar Plate by Pickling and Passivation

Corrosion resistance of Cu‐bearing 316L stainless steel tuned by various passivation potentials

Pitting Corrosion of 304 L Stainless Steel Welds in Simulated Concrete Pore Solutions

Passivation and Depassivation of HPB335 Carbon Steel in Simulated Concrete Pore Solution

Passivation Behavior on the Surface of Stainless Steel Reinforced by Quasicrystal-Abrasive Via Finite Element Simulation

Effect of liquid droplet impingement on electrochemical passivation behavior of 321 stainless steel in 0.5 wt.% NaCl solution

Electropolishing of 316L Stainless Steel for Anticorrosion Passivation

Passivation Behavior and Surface Chemistry of 2507 Super Duplex Stainless Steel in Acidified Artificial Seawater Containing Thiosulfate

Evaluation of Passive Films on 17-7PH and 410 Stainless Steel Exposed to NaCl Solution

The Acceleration of Pitting Corrosion of AISI 304 Stainless Steel by Ultraviolet Light Illumination in Acidic Chloride Solution

Corrosion mechanism of additively manufactured 316 L stainless steel in 3.5 wt.% NaCl solution

Effect of hydrogen on pitting corrosion of 2205 duplex stainless steel under alternating dry/wet marine environment

Obvious improvement in electrochemical and long-term immersion corrosion resistance of AISI 420 martensitic stainless steel using laser shock peening

Electrochemical corrosion and passive behavior of a new high-nitrogen austenitic stainless steel in chloride environment

Low-Temperature Oxy-Nitriding of AISI 304 Austenitic Stainless Steel for Combat Corrosion and Wear in HCl Medium

A Sequential Dual-Passivation Strategy for Designing Stainless Steel Used above Water Oxidation