Abstract:Superconducting spherical shells may not only provide an appealing platform for exploring superconductivity in three-dimensional (3D) geometries with curved surfaces, but also be practically applied in important fields, such as in gyroscopes and gravimeters. In inertial confinement fusion (ICF), the perturbation on the target capsule caused by traditional contact support methods is recognized as one of the major contributors to performance degradation in ICF implosions. It was proposed recently that coating the capsule with a thin superconducting MgB2 spherical shell to realize non-contact support by means of magnetic levitation at the required temperatures similar to 20 K might offer a promising solution to this longstanding problem. To simulate the coating of ICF capsules, we deposited MgB2 spherical shells onto polycrystalline Si3N4 spheres (diameter d= 2 mm and 1 mm) via a hybrid physical-chemical vapour deposition technique. For both diameters, the spherical shells, of about 1 mu m in thickness and covering the whole spheres completely, were polycrystalline with thin plate-shaped MgB2 crystallites oriented randomly and closely connected. The spherical shells exhibited superconducting transition at a zero resistance temperature T-c(zero) c of 38.5-39.4 K in four-probe resistance measurements and ideal diamagnetism at low temperatures in magnetization measurements, suggesting the good crystallinity and homogeneity of the shells. The upper critical field H-c2, the irreversibility field H-irr and the lower critical field H-c1 were characterized and showed similar magnitudes and temperature dependencies for the d= 2 mm and 1 mm shells, yielding H-irr of 7-8 T and H-c1 of 7-12 mT at 20 K. The superconducting critical current density J(c) values, evaluated from the magnetization hysteresis loops, were 1.8x10(6) A cm(-2) and 8.5x10(4) A cm(-2) at 20 K under zero and 2 T applied field, respectively, for the d= 1 mm shell. The occurrence of small flux jumps was observed at low temperatures up to 12 K and in low fields below 0.3 T. The results demonstrate the feasibility of fabricating MgB2 spherical shells with properties applicable to potential areas employing magnetic levitation such as in ICF and that MgB2 spherical shells may be exploited as an experimental system to study superconductivity in 3D curvilinear geometry.

Mg Gas Infiltration for the Fabrication of MgB2 Pellets Using Nanosized and Microsized B Powders

Infiltration effect of Mg with different matter states in the reaction of MgB 2 bulks

MgB2 Superconductor Prepared by Mg Diffusion Method with the Addition of Reduced Graphene Oxide

Microstructure and Superconducting Properties of MgB2 Bulks Prepared from Mg + B + Mg(BH4)2 Composites

Phase formation of polycrystalline MgB2 at low temperature using nanometer Mg powder

Coating Thick MgB 2 Layer on Stainless Steel Substrate

The mechanism of pore formation in superconducting MgB2 synthesized at low temperature by in-situ process

High-density MgB 2 superconducting bulk samples prepared at ambient pressure

In Situ Resistance Analysis of MgB2 Formation Process from Mg(BH4)2

MgB 2 Superconducting Joint Technique Based on Mg Diffusion Method

Low-temperature Sintering to Fabricate MgB2 by Using Mg(BH4)2 As Precursor

High-Temperature Synthesis of Superconducting MgB2 Materials in a Centrifuge

The Influence of Synthesis Parameters on Microstructures and Superconducting Properties of MgB2 Bulks

Film Fabrication and Electronic Devices of MgB2 Superconductor

Superconducting properties of nanocrystalline MgB$_2$

Significant Enhancement of Flux Pinning in Mgb2 Superconductor Through Nano-Si Addition

Properties of Superconducting MgB2 Spherical Shells Deposited on 2 Mm and 1 Mm Diameter Si3N4 Spheres

Influence of the Preparation Process on Microstructure, Critical Current Density and Tc of MgB2 Powder-In-Tube Wires

Improved Superconducting Properties in Bulk MgB2 Prepared by High Energy Milling of Mg and B Powder

A sol-gel method for growing superconducting MgB2 films

Superconducting Properties of MgB 2 Prepared by High Pressure and Ambient Pressure