Abstract:Co-free Li-rich Mn-based layered oxides (LRMLOs) are attractive cathode materials for lithium-ion batteries due to their low cost, high energy density and environmental friendliness. However, they also suffer from the drawbacks of low initial Coulombic efficiency, rapid voltage fading and capacity decay, and poor rate performance as the general LRMLO cathode, which prevent their practical applications. In the present work, a multilayer surface coating composed of Li 2 B 4 O 7 /B 2 O 3 and a spinel heterostructure rich-in oxygen vacancies are in-situ formed at the surface of the Co-free LRMLO particles by a facile thermal reduction treatment with NH 4 B 5 O 8 . The multilayer surface improves greatly the electron and ion conductivities, and plays significantly synergistic roles on suppressing oxygen release, reducing the dissolution of Mn and Ni elements, retarding the structure transformation from layered to spinel, and preventing the side reaction of the active material with electrolyte during cycling for the cathodes. As a result, the overall electrochemical properties of the cathodes are significantly improved. With an optimized addition of 10 wt% NH 4 B 5 O 8 , the initial Coulombic efficiency of the cathode is as high as 90.0%, and a capacity of 275 mAh g -1 is obtained at 0.1 C (1 C = 200 mA g -1 ) with the capacity retention of 98.5% after 100 cycles. A capacity of 194 mAh g -1 is maintained after 300 cycles at 1 C, with the capacity retention of 92.8%. A capacity of 117 mAh g -1 is obtained at a high rate of 20 C. In addition, the voltage fading during cycling is also greatly inhibited. The structure evolution of the cathode material during cycling is systematically investigated and the mechanism for the improved electrochemical properties is proposed. The present work provides a new surface structure design strategy and the method for enhancing the overall electrochemical performance of Co-free Li-rich Mn-based layered oxide cathodes.

Bifunctional Surface Modification Coupled with Oxygen Defect Engineering Enables High Performance Li-rich Cathodes

Surface Modification and Electrochemical Properties of Li-Rich Layered Cathode Materials for Lithium-Ion Batteries

In-situ surface chemical and structural self-reconstruction strategy enables high performance of Li-rich cathode

Constructing a robust integrated surface structure for enhancing the performance of Li-rich Mn-based oxides cathodes

Suppressing Bulk Strain and Surface O2 Release in Li-Rich Cathodes by Just Tuning the Li Content

Mitigating Evolution of Lattice Oxygen and Stabilizing Structure of Lithium-Rich Oxides by Fabricating Surface Oxygen Defects

Surface Coupling between Mechanical and Electric Fields Empowering Ni‐Rich Cathodes with Superior Cyclabilities for Lithium‐Ion Batteries

Multifunctional surface structure with enhanced electron and ion conductivities for superior electrochemical performance of Co-free Li-rich Mn-based layered oxide cathodes

Surface Engineering Donor and Acceptor Sites with Enhanced Charge Transport for Low-Overpotential Lithium–oxygen Batteries

Surface Miscible Structure Modulation of Li‐Rich Cathodes by Dual Gas Surface Treatment for Super High‐Temperature Electrochemical Performance

Modulating Surface Architecture and Electronic Conductivity of Li-rich Manganese-Based Cathode

Constructing uniform oxygen defect engineering on primary particle level for high-stability lithium-rich cathode materials

In Situ Induced Lattice‐Matched Interfacial Oxygen‐Passivation‐Layer Endowing Li‐Rich and Mn‐Based Cathodes with Ultralong Life

In Situ Surface Coating and Oxygen Vacancy Dual Strategy Endowing a Li-Rich Li 1.2 Mn 0.55 Ni 0.11 Co 0.14 O 2 Cathode with Superior Lithium Storage Performance

Catalytic Strategies Enabled Rapid Formation of Homogeneous and Mechanically Robust Inorganic‐Rich Cathode Electrolyte Interface for High‐Rate and High‐Stability Lithium‐Ion Batteries

In Situ Surface Reaction for the Preparation of High-Performance Li-Rich Mn-Based Cathode Materials with Integrated Surface Functionalization

Structural self-reconstruction strategy empowering Ni-rich layered cathodes with low-strain for superior cyclabilities

Surface modification single crystal Li-rich Li1.2Mn0.54Ni0.13Co0.13O2 as high performance cathode materials for Li-ion batteries

Enhancing cycling stability in Li-rich Mn-based cathode materials by solid-liquid-gas integrated interface engineering

Cathode Electrolyte Interface Engineering by Gradient Fluorination for High‐Performance Lithium Rich Cathode

Enhanced Cycling Stability of Lithium-Rich Cathode Materials Achieved by in-situ Formation of LiErO2 Coating