Abstract:Abstract Fast EDM (electrical discharge machining) drilling is a powerful machining technique dedicated for small hole machining (0.2mm~3mm in diameter). It employs rotary tubular electrode and water-based dielectric fluid with high-pressure inner flushing. Owing to the enhanced inner flushing, evacuation of debris from the discharge gap becomes much easier. Therefore it can achieve higher machining efficiency than conventional sinking EDM and is capable of drilling high aspect-ratio (100:1 and higher) holes. It has now been widely used to drill small holes in manufacturing industries such as molds \u0026 dies, filters, automotive and aerospace parts. Fast EDM drilling process is a typical time-variant process, especially when drilling high aspect-ratio holes. The machining condition changes with time as the electrode goes deeper, since the evacuation of debris becomes increasingly difficult and the machining condition deteriorates. The conventional control system of the process determines the feedrate by average gap voltage with its parameters unchanged during the process. Such control systems become less efficient when drilling high aspect-ratio holes. In this paper, an adaptive control system for fast EDM drilling is proposed to deal with this complex process. The controlled plant is considered as a double-input double-output (DIDO) system. The inputs are the servo-reference voltage and the gain of the original controller, and the outputs are the ratio of normal discharge state (NDR) and its variance in a time interval. The servo-reference voltage is a key parameter for the control of the process, while the gain determines the actual feedrate along with the servo-reference voltage. The adaptive control system first estimates the parameters of the controlled plant model, and then automatically adjusts the two inputs according to current outputs and desired ones. The time-variant parameters of the controlled plant are estimated by the recursive least squares (RLS) method with a forgetting factor. And the multivariable generalized minimum variance method is used to obtain the control law of the two inputs. Experiments were conducted to verify the effectiveness of the controller, where 40-mm-deep holes were drilled by electrodes with a diameter of 0.4 mm (aspect-ratio 100:1). The results show that the machining state was improved by the adaptive controller especially in the later stage of the drilling process. NDR was higher and short circuits were suppressed. Results show that machining time was reduced by 11.3% and tool wear was also reduced by 3.0% with the adaptive controller.

Study on Dynamically Variable Attitude EDM Machining Method of Deep Narrow Slots

Influence of electrode feed directions on EDM machining efficiency of deep narrow slots

Study on Particle Size Distribution of Debris in Electrical Discharge Machining of Deep Narrow Slots

Experiment Research for Deep-Small Hole Drilling by EDM

Experimental Investigation to Improve the Efficiency and Surface Integrity of Deep Micro-Hole Machined by Micro-Edm

Electrochemical milling of deep-narrow slots with a pulsating electrolyte flow field

Study on Electrode Vibration in the Touch-Down Stage of Fast Electrical Discharge Machining Drilling

Study on material removal mechanism and control strategy of multi-axis fast ED-milling

Influence of Alternating Side Gap on Micro-Hole Machining Performances in Micro-Edm

Spatial Planetary Movements for Multi-Axis EDM

An Investigation into Accumulative Difference Mechanism in Time and Space for Material Removal in Micro-EDM Milling

Performance improvement of high-speed EDM and ECM combined process by using a helical tube electrode with matched internal and external flushing

High-speed Near Dry Electrical Discharge Machining

Pulse Dynamic Regulation of Electrochemical Discharge Milling by Utilizing the Slotted Tube Electrode

Study on machining characteristics of magnetic field assisted micro-EDM with ultrasonic vibration of workpiece

Completion Detection and Efficiency Improvement for Breakout Stage of Fast EDM Drilling

Gap Flow Research for Deep-Small Hole Drilling by EDM Based on Fluent Software

Experimental study of EDM milling of 3D-shaped diffuser for film cooling holes on turbine blades

Adaptive Control for Fast EDM Drilling of High Aspect-Ratio Holes

Machining performance enhancement of deep micro drilling using electrochemical discharge machining under magnetohydrodynamic effect

Experimental Study and Parameter Optimization on Sustainable and Efficient Machining GH4169 with Rotating Short Arc Milling Method