Abstract:Organic-inorganic metal halide perovskite solar cells (PSCs) have been widely studied due to their excellent photoelectric conversion performance, but the inherent chemical instability of CH(NH 2 ) 2 PbI 3 (FAPbI 3 ) has hindered its long-term development. In particular, the surface interface of the membrane has prominent humidity sensitivity due to lower activation energy, the defect of the surface interface has a strong correlation with the film stability, and the treatment result of the defect is one of the key factors to improve the long-term stability. FAPbI 3 suffers phase transition from black perovskite phase to yellow non-perovskite phase at room temperature, and the moisture will accelerate this phase transition. Interface engineering is one of the common methods to improve the stability of perovskite solar cells. In addition to interface engineering, there is also a strategy of stacking a two-dimensional (2D) perovskite layer on the surface for interface passivation. However, the preparation methods of 2D perovskite layer are most limited. In this paper, through the preparation process of the whole solution method and post-treatment mode of annealing were adopted, the hybrid perovskite solar cells of vitamin perovskite were successfully prepared. FAPbI 3 perovskite surface was uniformly spin-coated with butylamine iodide (BAI) solution, and the formation of 2D perovskite was driven on the surface of FAPbI 3 perovskite. Due to the passivation of 2D perovskite layer on the defects at the surface interface, the carrier non-radiative recombination is reduced, so that the carrier lifetime is greatly improved. Due to the hydrophobicity of long chain molecules in 2D perovskite, the long-term stability of the device has been significantly improved. Consequently, the unencapsulated device containing 2D perovskite layer remained above 80% after working nearly 1000 hours of relative humidity (RH) of 60% in ambient air at room temperature. The 2D perovskite layer can significantly improve the long-term stability of the film without affecting the charge carrier transport performance. This method to improve the stability of the device by constructing 2D perovskite layer is in line with the requirements and development trend of high-quality perovskite solar cells, and is a strategy with great development potential.

Maximizing Merits of Undesirable Δ‐fapbi3 by Constructing Yellow/black Heterophase Bilayer for Efficient and Stable Perovskite Photovoltaics

Complex Additive‐Assisted Crystal Growth and Phase Stabilization of α‐FAPbI3 Film for Highly Efficient, Air‐Stable Perovskite Photovoltaics

Polymerization stabilized black-phase FAPbI3 perovskite solar cells retain 100% of initial efficiency over 100 days

Oriented Nucleation in Formamidinium Perovskite for Photovoltaics

Vapor-assisted deposition of highly efficient, stable black-phase FAPbI 3 perovskite solar cells

Vapor-assisted Deposition of Highly Efficient, Stable Black-Phase FAPbI3 Perovskite Solar Cells.

Surface defect passivation by 1,8-Naphthyridine for efficient and stable Formamidinium-based 2D/3D perovskite solar cells

Preparation of 2D Perovskite Layer by Solution Method to Improve the Stability of FAPbI 3 Perovskite Solar Cells

Stable α‐FAPbI3 via porous PbI2 for efficient perovskite solar cells

A Self‐Assembled 3D/0D Quasi‐Core–Shell Structure as Internal Encapsulation Layer for Stable and Efficient FAPbI 3 Perovskite Solar Cells and Modules

Synergetic Co‐Modulation of Crystallization and Co‐Passivation of Defects for FAPbI 3 Perovskite Solar Cells

A Self-Assembled 3D/0D Quasi-Core-Shell Structure As Internal Encapsulation Layer for Stable and Efficient FAPbI3 Perovskite Solar Cells and Modules

Stabilizing the Α-Phase of CsPbI3 Perovskite by Sulfobetaine Zwitterions in One-Step Spin-Coating Films

Efficient and Stable FAPbBr3 Perovskite Solar Cells Via Interface Modification by a Low-Dimensional Perovskite Layer

Enhancing Performance and Stability of Perovskite Solar Cells with a Novel Formamidine Group Additive

Nanoscale phase management of the 2D/3D heterostructure toward efficient perovskite solar cells

Synchronous Elimination of Excess Photoinstable PbI2 and Interfacial Band Mismatch for Efficient and Stable Perovskite Solar Cells

Surface charge-transfer doping for highly efficient perovskite solar cells

Defect suppression and energy level alignment in formamidinium-based perovskite solar cells

Stabilization of FAPbI3 with Multifunctional Alkali‐Functionalized Polymer

Amide‐Catalyzed Phase‐Selective Crystallization Reduces Defect Density in Wide‐Bandgap Perovskites