Abstract:Stacking fault energy (SFE) can play a crucial role in plastic deformation and damage mechanisms of face-centered cubic (fcc) metals. This study mainly summarized the following results: (1) With the reduction of SFE, the slip mode of fcc metals gradually changes from a facile cross-slip wavy mode to a planar mode until deformation twinning occurs; (2) The concept of effective SFE is applied to investigate the variation of SFE with dislocation density in the fcc metals, with the increase in dislocation density, the effective SFE increases; (3) The reduction of SFE is not the only factor determining the formation of deformation twins in fcc metals. In terms of calculating the competition between simulated slipping and twinning using the first principles, the critical criterion for forming deformation twinning in fcc metals was established; (4) The fatigue dislocation configuration of high-, medium-, and low-SFE fcc metals were analyzed and the judgment conditions for forming regular persistent slip bands (PSBs) are proposed; (5) With the increase in Al content, the SFE of Cu-Al alloy decreases, resulting in a simultaneous increasing trend in the tensile strength and the uniform elongation due to the increasing planar slip degree; (6) The exponential strain-hardening model can accurately describe the tensile strain-hardening process of Cu-Al alloys. The quantitative relationship among yield strength, tensile strength, and uniform elongation of Cu-Al alloy with different alloy compositions and microstructure states was successfully predicted; (7) With the increase in Al content, the fatigue strength of Cu-Al alloy is improved. Increasing Al content at the same strain amplitude will enhance its low-cycle fatigue life. Based on the experimental results above, it is shown that the alloy composition affects the deformation and damage mechanisms, and the evolution process of microscopic defects (dislocations, twins) in fcc metals and alloys. Thus, it drastically affects the tensile and fatigue properties of the fcc metals and alloys. These results provide experimental evidence and a theoretical basis for improving the mechanical properties and service reliability of fcc metals and alloys via alloy designing.

In-situ TEM Study on the Effect of Stacking Faults on Micro-Plasticity and Proportional Limit in SiC/Al Composites

Higher Proportional Limit of SiC/Al Composites with Nano-Scaled Stacking Faults

Synergistic Strengthening of Al–SiC Composites by Nano-Spaced SiC-nanowires and the Induced High-Density Stacking Faults

Strength-ductility synergy induced by high-density stacking faults in aluminum alloy composites with micro/nano hybrid reinforcements

Stacking faults in a mechanically strong Al(Mg)–Al3Mg2 composite

Achieving Simultaneous Enhancement of Strength and Ductility in Al Matrix Composites by Employing the Synergetic Strengthening Effect of Micro- and Nano-Sicps

In situ mechanical testing of an Al matrix composite to investigate compressive plasticity and failure on multiple length scales

3D Microstructure-based Finite Element Modeling of Deformation and Fracture of SiCp/Al Composites

Effects of stacking fault energy on the deformation behavior of CoNiCrFeMn high-entropy alloys: A molecular dynamics study

Effects of Stacking Fault Energy on the Deformation Mechanisms and Mechanical Properties of Face-Centered Cubic Metals

Effects of SMAT Temperature and Stacking Fault Energy on the Mechanical Properties and Microstructure Evolution of Cu-Al-Zn Alloys

Unstable stacking faults in submicron/micron Al grammins in multi-SiCp/multi-Al nanocomposite

Understanding the Micromechanical Behaviors of Particle-Reinforced Al Composite by Nonlocal Crystal Plasticity Modeling

Synergistic Interface Effects on Mechanical Properties: in Situ Study on Fracture Behaviors of Al Matrix Composite Joint

Deformation and fracture of SiCp/Al composites under complex loading conditions: A simulation study

Dislocation Extension in Coarse–grained Al Reinforced by SiC Nanowires under Complex Stress Condition

Ab Initio Molecular Dynamics Simulation of the Effects of Stacking Faults on the Radiation Response of 3C-Sic

Microstructure Evolution and Mechanical Behaviors of SiCp/CNTs Hybrid Reinforced Al-Si-Cu-Mg Composite by Semi-solid Stir Casting

Microstructure evolution and mechanical properties of selective laser melting fabricated hybrid particle reinforced AlSi10Mg composites

Fracture Mechanism of Nano- and Submicron-Sicp/mg Composite During Room Temperature Tensile Test: Interaction Between Double Sized Particles and Dislocations

Mechanical Behavior and Interfacial Micro-Zones of SiCp(CNT) Hybrid Reinforced Aluminum Matrix Composites