Abstract:Magnesium alloy is regarded as a lightest engineering structural metal material due to its low density, but its wide application is limited due to poor plastic deformation behavior. Therefore, the comprehensive mechanical properties of enhanced magnesium alloy have become a research focus in the material science. Here, the effect of graphene on the deformation behavior and that on the mechanical properties of magnesium under tensile loading are studied by molecular dynamics simulation. The results show that the introduction of graphene can significantly improve the mechanical properties of pure magnesium. Comparing with pure magnesium, the Young's modulus and the first peak stress of the graphene magnesium matrix (GR/Mg) composites are increased by about 27.5% and 36.5% respectively, which is mainly due to the excellent mechanical properties of graphene. The results also indicate that the embedded position of graphene has little effect on the Young's modulus or peak stress of the GR/Mg composites, but it will significantly affect the plastic deformation behavior of the GR/Mg composites after the second peak stress. With the increase of the embedded height of graphene, the average flow stress of the GR/Mg composites first increases in the later stage of plastic deformation. When the embedded height reaches 0.4 L , the average flow stress of the GR/Mg composites reaches a maximum value, and then decreases. This phenomenon of the Gr/Mg composites can be explained by the plastic deformation behavior of the magnesium matrix above and below graphene. The embedded position of graphene has a great influence on the plastic deformation behavior of the upper and lower magnesium matrix of the GR/Mg composites. When the embedded height of graphene is small, the plastic deformation capability of magnesium matrix under graphene is strong and dislocation slip is easy to occur. And when the embedded height of graphene is large, the plastic deformation capabilities of the two parts of magnesium matrix above and below graphene are equal, and their plastic deformation behavior tends to be synchronous. The results show that the plastic deformation behavior of the GR/Mg composite is the same as that of pure magnesium, and the phase transition from HCP to BCC and then to HCP occurs in the process of the plastic deformation. The phase transition mechanism of magnesium matrix is also analyzed in detail. The results of this study have certain theoretical guiding significance in designing the high performance graphene metal matrix composites.

Achieving High Strength and Modulus in Graphene Reinforced Mg Matrix Composites Via an In-Situ Process

Microstructural Evolution in Graphene Nanoplatelets Reinforced Magnesium Matrix Composites Fabricated Through Thixomolding Process

Research progress on preparation technology of graphene-reinforced aluminum matrix composites

Enhancing the Mechanical Properties of AM60B Magnesium Alloys through Graphene Addition: Characterization and Regression Analysis

Graphene Nanoplatelets Reinforced Magnesium Matrix Composites Fabricated by Thixomolding

Fabrication of magnesium-coated graphene and its effect on the microstructure of reinforced AZ91 magnesium-matrix composites

Development of AZ91D Magnesium Alloy-Graphene Nanoplatelets Composites Using Thixomolding Process

Microstructure and Mechanical Properties of Magnesium Matrix Composites Reinforced by In Situ Reduced Graphene Oxide

Investigation of graphene nanoplatelets-deposited textured metal matrix composite plates for improved mechanical properties: a numerical approach

A review of the design, processes, and properties of Mg-based composites

Effect of MgO particles with in-situ graphene coating on mechanical and thermal expansion properties of aluminum matrix composites

Achieving high strength in graphene nanoplatelets reinforced Mg-Zn-Mn matrix composites via liquid-state molding technology and low temperature deformation process

Ameliorating the Strength-Modulus Synergy in GNPs Reinforced Mg–Zn–Zr Composites via Multidirectional Forging and Hot Extrusion Deformation

Effect of Processing Techniques on Interface Bonding of Graphene Reinforced Metal Matrix Composites: A Review

High strength and conductivity copper matrix composites reinforced by in-situ graphene through severe plastic deformation processes

High strength and high electrical conductivity in copper reinforced with intra-/inter-granular graphene in-situ exfoliated from graphite

Effect of graphene on microstructure, strain hardening and corrosion behaviour of dual phase Mg-Li matrix processed through liquid metallurgy route

Mechanical behavior of graphene magnesium matrix composites based on molecular dynamics simulation

Interfacial properties and strengthening mechanisms of few-layered MXene reinforced Mg-based composites

Microstructure and tribological properties of Mg matrix composite reinforced with modified graphene

Enhancing the Strengthening Effect of Graphene-Nanoplates in Al Matrix Composites by Heterogeneous Matrix Design