Abstract:The modern rhythm of human life leads to well-known problems, which are air, water and soil pollution and climate warming. An increase in the power of industries and vehicles leads not only to atmospheric pollution by-products of incomplete fuel combustion but also to various microscopic particles that form aerosols, which carry an obvious danger to human health and also pollute the buildings' facades. An environmentally friendly building material with a hybrid method "Nano-titania gradient" was developed. This method consists of forming a gradient of n-TiO2 particles concentration in the composite since the physical properties of the composite are always inextricably linked to the geometry. To increase the efficiency of the photocatalytic process, a method of surface sensitization of titanium dioxide with the use of graphene oxide was proposed, which contributed to an increase in the overall photosensitivity. Thus, the decomposition of nitrogen oxide by volume with the modified surface increased by 27% in comparison with the classic titanium dioxide, and the decomposition of volatile organic substances increased by 32%. It was found that for the facade plate made with surface-sensitized TiO2, the process of self-cleaning is completed after 3 h after the irradiation start. The modern rhythm of human life leads to well-known problems, which are air, water and soil pollution and climate warming. Using the theory of percolation, the concentration range of the photocatalyst content was calculated. To facilitate the material, waste cellulose was introduced. To increase the efficiency of the photocatalytic process, a method of surface sensitization of titanium dioxide (SS TiO2) with the use of graphene oxide was proposed. The analysis of the experimental-statistical models of the compressive strength shows that the optimum content of TiO2 was in the range from 0.8 to 1.1%, and cellulose from 0.4 to 0.8%, the optimum content of SS TiO2 was in the range from 0.7 to 1.1%, and cellulose from 0.4 to 0.8%. Analysis of the experimental and statistical model of the bending strength shows that the optimal content of TiO2 and SS TiO2 was in the range of 0.6 to 1.0%, and cellulose from 0.4 to 0.8%. When studying the structure of composites, it was found that titanium dioxide was sorbed on the surface of swollen cellulose fibers and remained there after the process of cement hydration. The effectiveness of the method of surface sensitization of titanium dioxide by combining it with graphene oxide was shown. Thus, the decomposition of nitrogen oxide by volume with the modified surface increased by 27% in comparison with the classic titanium dioxide, and the decomposition of volatile organic substances increased by 32%. It was found that for the facade plate made with surface-sensitized TiO2, the process of self-cleaning was completed after 3 h after the irradiation start.

Variation of self-cleaning performance of nano-TiO<sub>2</sub> modified mortar caused by carbonation: From hydrates to carbonates

Evaluation of self-cleaning performance of TiO2-intermixed and TiO2-coated cement mortars under natural sunlight

Synthesis of TiO2 Based Superhydrophobic Coatings for Efficient Anti-Corrosion and Self-Cleaning on Stone Building Surface

Surface properties and de-polluting performance of a photocatalytic coating incorporating novel core@shell nanospheres for cementitious substrate

Influences of titanium dioxide nanoparticles on regulation of crystalline growth and early carbonation of cementitious composites

Effects of the use of TiO2 on the early ages of white cement-based mortars: analysis of chemical, physical, mechanical, and photocatalytic properties

Development of photocatalytic carbonation coating for concrete: Enhancement of air quality and sequestration of CO2

Carbonation of photocatalytic aluminosilicate cement composites: Evolution of self-cleaning and radiative cooling properties

The Effect of TiO2 Doped Photocatalytic Nano-Additives on the Hydration and Microstructure of Portland and High Alumina Cements

NO x degradation by cement mortar containing B-TiO 2 /MgAl-CLDH under visible light: Experimental and modeling

Effect of Nano-Tio2 on the Mechanical Properties of Cement Mortar

Self-Cleaning Cement-Based Building Materials

Compatibility and Photocatalytic Capacity of the Novel Core@shell Nanospheres in Cementitious Composites

Analyzing the Effects of Nano-Titanium Dioxide and Nano-Zinc Oxide Nanoparticles on the Mechanical and Durability Properties of Self-Cleaning Concrete

Interface Actions Between TiO2 and Porous Diatomite on the Structure and Photocatalytic Activity of TiO2-diatomite

Quantitative Analysis of Carbonation Degree of Mortar Based on Multiple Interactive Influences

Multiscale pore structure analysis of nano titanium dioxide cement mortar composite

Experimental investigation on the effect of incorporating nanomaterials on some properties of self-compacting cementitious mortar

Self-cleaning performance of autoclaved photocatalytic cement pastes: Insights into phase composition, microstructure and aluminum incorporation in C–S–H

Application of Supported TiO2 in Carbonated Binding Material and Its Photocatalytic Performance

Self-cleaning durability assessment of TiO2/SiO2 photocatalysts coated concrete: Effect of indoor and outdoor conditions on the photocatalytic activity