Abstract:Piezoelectric wafer active sensors (PWAS) have been proven a valuable tool in structural health monitoring. Piezoelectric wafer active sensors are able to send and receive guided Lamb/Rayleigh waves that scan the structure and detect the presence of incipient cracks and structural damage. In-situ thin-film active sensor deposition can eliminate the bonding layer to improve the durability issue and reduce the acoustic impedance mismatch. Ferroelectric thin films have been shown to have piezoelectric properties that are close to those of single-crystal ferroelectrics but the fabrication of ferroelectric thin films on structural materials (steel, aluminum, titanium, etc.) has not been yet attempted. In this work, in-situ fabrication method of piezoelectric thin-film active sensors arrays was developed using the nano technology approach. Specification for the piezoelectric thin-film active sensors arrays was based on electro-mechanical-acoustical model. Ferroelectric BaTiO3 (BTO) thin films were successfully deposited on Ni tapes by pulsed laser deposition under the optimal synthesis conditions. Microstructural studies by X-ray diffractometer and transmission electron microscopy reveal that the as-grown BTO thin films have the nanopillar structures with an average size of approximately 80 nm in diameter and the good interface structures with no inter-diffusion or reaction. The dielectric and ferroelectric property measurements exhibit that the BTO films have a relatively large dielectric constant, a small dielectric loss, and an extremely large piezoelectric response with a symmetric hysteresis loop. The research objective is to develop the fabrication and optimum design of thin-film active sensor arrays for structural health monitoring applications. The short wavelengths of the micro phased arrays will permit the phased-array imaging of smaller parts and smaller damage than is currently not possible with existing technology.

Flexible Mechanical Sensor Based on Epitaxial BaTiO3 Films with Biaxial Anisotropy

Ferroelectric Thin-Film Active Sensors for Structural Health Monitoring

Piezoelectric Polyacrylonitrile Nanofiber Film-Based Dual-Function Self-Powered Flexible Sensor.

Towards a Large-Area Freestanding Single-Crystal Ferroelectric BaTiO3 Membrane

Flexible Lead-Free BaTiO3 Ferroelectric Elements with High Performance

A freestanding ferroelectric thin film-based soft strain sensor

[Development of flexible multi-phase barium titanate piezoelectric sensor for physiological health and action behavior monitoring]

Flexible Tensile Strain Sensor Based on Lead-Free 0.5ba (ti0.8zr0.2) O3–0.5(Ba0.7Ca0.3) TiO3 Piezoelectric Nanofibers

Flexible piezoelectric pressure sensor based on BaTiO3-CNT/RTV Composite Film with Filter Paper Microstructures for Monitoring Hand Motions

Flexible and wearable BaTiO3/polyacrylonitrile-based piezoelectric sensor for human posture monitoring

High-Performance Flexible PLA/BTO-Based Pressure Sensor for Motion Monitoring and Human–Computer Interaction

Ultraflexible and Malleable Fe/BaTiO<sub>3</sub> Multiferroic Heterostructures for Functional Devices

Highly Heterogeneous Epitaxy of Flexoelectric BaTiO3-δ Membrane on Ge.

A Flexible Strain Sensor of Ba(Ti, Nb)O3/Mica with a Broad Working Temperature Range

Flexible room-temperature multiferroic thin film with multifield tunable coupling properties

Ultraflexible and Malleable Fe/BaTiO 3 Multiferroic Heterostructures for Functional Devices

High‐Performance Ultrasensitive Flexible Piezoelectric Thin Film Sensors Via a Cost‐Effective Transfer Strategy

Low-entropy structured wearable film sensor with piezoresistive-piezoelectric hybrid effect for 3D mechanical signal screening

A Novel Flexible Tactile Sensor Based on Ce-Doped Batio3 Nanofibers

Ultrasmall Barium Titanate Nanoparticles Modulated Stretchable Dielectric Elastomer Sensors with Large Deformability and High Sensitivity

Self-powered Flexible Piezoelectric Sensors Based on Self-Assembled 10 Nm BaTiO₃ Nanocubes on Glass Fiber Fabric