Abstract:With the further development of intelligent robots, bionic touch sensing has become an important means for the robotic dexterous hand to interact with the external environment, making it a hot topic. However, in the existing research on tactile perception of robotic hands, most of the sensing units have complex structures and are difficult to integrate in the hand. For touch sensing of the dexterous robot hand, this work employs optical Fiber Bragg Grating(FBG)as the information transmission and sensing carrier and develops a wearable touch fingerstall. The thumb fingerstall contains two segments:fingertip and finger pulp. The fingertip is composed of a curved surface and a plane surface. The curved surface can fit the thumb shape better, and the plane surface can provide a more stable touch. Specially, we use a cylindrical pin as the knuckle to connect the fingertip and finger pulp. The touch sensing of three contact positions of the fingerstall have been studied: position 1 is the vertical fingertip, position 2 is the 15 degrees fingertip, and position 3 is the 30 degrees finger pulp. Firstly, the fingerstall model was simulated using the finite element method to verify its structural feasibility. Then, the fingerstall was loaded using an electronic tension machine, ranging from 0 N to 10 N with a 1 N increment, and each load was held for 25 s. For each test position, the experiment was repeated three times, and the responses of FBG were recorded. Analysis of the touch sensing experimental data shows that the sensing fingerstall has good sensitivity and linearity within the 0 similar to 10 N touch pressure range. The average sensitivities at position 1, position 2, and position 3 are 24.119 6 pm/N, 10.338 3 pm/N, and - 1.580 7 pm/ N, respectively, with linearity above 99%. Overall, the simulation results are basically consistent with the experimental results, although some errors may arise due to 3D printing and FBG packaging. Therefore, different loading positions and forces can be distinguished by different center wavelength offset and offset direction of FBG. In order to verify the sensing performance of the fingerstall further, a hardness discrimination experiment was carried out primarily focused on perceiving objects of small hardness. And the standard ratio of wavelength to touch depth (k(s)) was proposed as a quantitative measure of hardness perception. Position 1 was selected as the experimental position for hardness perception, and four silicone blocks with different hardness (named as 0 HA, 10 HA, 20 HA and 40 HA) were selected as the experimental objects. Considering the time and safety factors, 5 mm was selected as the touching depth, and 60mm/ min as the touching speed. The average responses of FBG to 0 HA, 10 HA, 20 HA and 40 HA are 58.57 pm, 242.3 pm, 580.95 pm, 1107.6 pm, respectively. The corresponding k(s) values are 11.717 pm/mm, 48.46 pm/mm, 116.19 pm/mm and 221.52 pm/mm, respectively. According to the data results, when the fingerstall touches the 40 degrees silicone block, the k(s) is the largest, and the k(s) is the smallest at the 0 degrees silicone block. When k(s) is larger, the greater the hardness of the object is. The sensing fingerstall has a good repetition, with repeatability errors of 3.82%, 0.97%, 0.51%, and 0.29%.In conclusion, a simple and wearable fingerstall has been designed. The tactile sensitivity of three different position has been studied, and a hardness discrimination experiment has been conducted. These research results can serve as a basis for bionic touch sensing of dexterous robotic hands.

Three-Fingers FBG Tactile Sensing System Based on Squeeze-and-Excitation LSTM for Object Classification

FBG Tactile Sensing System Based on GAF and CNN

Optical Fibre Bragg Based Sliding-tactile Sensing and Classification Training Method for Material Recognition

Fiber Bragg grating tactile perception system based on cross-modal transformer

Object Tactile Classification Based on Convolutional Spiking Neural Network with Attention Mechanism

Research on FBG Tactile Sensing Shape Recognition Based on Convolutional Neural Network

Design and tactile classification of flexible tactile sensor for soft gripper

Linear Dynamic System Method for Tactile Object Classification

A Skin-Inspired PDMS Optical Tactile Sensor Driven by a Convolutional Neural Network

A soft robotic system imitating the multimodal sensory mechanism of human fingers for intelligent grasping and recognition

Multifunctional Tactile Sensors for Object Recognition

A Fingertip Optical Fiber Composite Sensor with Conformal Design for Robotic Perception of Tactile Force

Design and Experimental Research of Robot Finger Sliding Tactile Sensor Based on FBG

Tactile Grasp Stability Classification Based on Graph Convolutional Networks

A Bio‐Inspired Artificial Tactile Sensing System Based on Optical Microfiber and Enhanced by Neural Network

Bionic Touch Sensing of Wearable Fingerstall Based on Optical Fiber Bragg Grating

Object classification based on the tactile sequence

Tactile-GAT: tactile graph attention networks for robot tactile perception classification

Tactile Glove-Decode and Classify the Human Grasping Process

Open‐Environment Tactile Sensing System: Towards Simple and Efficient Material Identification

A multisensory-feedback tactile glove with dense coverage of sensing arrays for object recognition