Abstract:In present study, the creep behavior of (TiB + TiC+Y2O3)/α-Ti composite with C-1 and C-2 microstructure were investigated with applied stress of 200 MPa and at 650–700 °C. The steady state creep rate increased by an order of magnitude from 650 °C to 700 °C, and the C-2 microstructure shown worse creep performance compared to C-1 microstructure. The creep activation energy of C-1 and C-2 microstructure were 359.5 kJ/mol and 380.2 kJ/mol, respectively, which were higher than the lattice diffusion in α-Ti. And the less QG due to coarse microstructure was responsible for its higher creep activation energy in C-2. In addition to cracks were observed at β grain boundary, α colony boundary, α/β phase boundary, they were also observed near the fracture TiB whiskers and near decohesion reinforcements. The cracks in C-2 were mainly concentrated near the reinforcement, while those in C-1 were mainly concentrated in the matrix part. Further analysis confirmed that the creep deformation mechanism of C-2 microstructure was controlled by reinforcements, but the creep deformation mechanism of C-1 microstructure was controlled by matrix microstructure. Summarily, the effect of reinforcement on creep deformation of (TiB + TiC+Y2O3)/α-Ti composite could be divided in two aspect: microstructure influence and the reinforcement itself. For reinforcement itself, it indeed affected the dislocation movement and creep fracture behavior, and then improved the creep performance. However, for microstructure influence, the fine grain (more grain boundary), coarsen microstructure (more equiaxed characteristics of α lamellar) caused more grain boundary slip to participate in creep deformation, which in turn deteriorated creep performance. In this study, the latter effect was somewhat bigger.

Quasi-in-situ Investigation on Microstructure Degradation of a Fully Lamellar TiAl Alloy During Creep

Creep-Induced Phase Instability and Microstructure Evolution of a Nearly Lamellar Ti–45Al–8.5Nb–(W, B, Y) Alloy

Creep of Ti–5Al–5Mo–5V–1Fe–1Cr Alloy with Equiaxed and Lamellar Microstructures

The microstructure evolution and phase transformation behavior of a β-solidifying γ-TiAl alloy during creep

Microstructural Characterization of Creep Cavitation in a Fully-Lamellar TiAl Alloy

The microstructure evolution and phase transformation behavior of a -solidifying ?-TiAl alloy during creep

Microstructure Evolution and Precipitation Behavior in a Y2O3-bearing TiAl Alloy During Creep

Microstructures and Creep Behavior of As-Cast TiAl-Nb Alloy

Creep Induced Alpha(2)->Beta(2) Phase Transformation In A Fully-Lamellar Tial Alloy

Microstructure Evolution Mechanisms in Nickel-Based Single Crystal Superalloys under Multiaxial Stress State

Creep Behavior and Related Phase Precipitation of a Creep-Resistant Y2O3-bearing High Nb Containing TiAl Alloy

Creep Behaviour of Equiaxed Fine-Grain Γ-Tial-based Alloy Prepared by Powder Metallurgy

Brittle–ductile Transition During Creep in Nearly and Fully Lamellar High-Nb TiAl Alloys

Creep behavior and effects of heat treatment on creep resistance of Ti-22Al-24Nb-0.5Mo alloy

Microstructural stability and creep properties of middle Nb γ-TiAl alloy with a modulated microstructure

The creep behavior of (TiB + TiC + Y2O3)/α-Ti composites at high temperature and short-term

Creep Behavior of High‐Nb TiAl Alloy at 800–900 °C by Directional Solidification

In Situ Observation of High Nb Containing TiAl Alloy in Creep Deformation

Twins and Β0 Precipitation Effects on the Lamellar Degradation in Tnm Alloy During Creep

Sub/micro-structural evolution of a Co-Al-W Ta-Ti single crystal superalloy during creep at 900 C and 420 MPa

Impact of Long-Term Thermal Exposure on the Microstructure and Creep Resistance of (Tib+tic+y2o3)/α-Ti Composite