Abstract:The production of hydrogen via photoelectrochemical (PEC) water splitting using III-V semiconductors as photoelectrodes is a field of current research and challenges in materials science. Under PEC conditions relevant to water splitting, III-V semiconductors are prone to corrosion and suffer from corrosion-related decrease of efficiency, which so far impedes long-term usage of III-V semiconductor-based photoelectrodes. Gallium phosphide (GaP) has an indirect band gap of 2.26 eV which covers both the hydrogen evolution potential (HEP) and the oxygen evolution potential (OEP). Thus, in principal, GaP can be used both as photocathode and photoanode. Notwithstanding the favorable band gap energy, the use of GaP photoelectrodes for the photolysis of water has so far not been successful without applying an additional bias potential. In this contribution we demonstrate that, by specific surface conditioning, we are able to control and optimize the photoelectrochemical surface properties of photoanodes prepared from n-doped GaP(100) for PEC water splitting. We have studied the structural and chemical surface modifications of such photoanodes before and after extended PEC processes by scanning electron microscopy (SEM), atomic force microscopy (AFM), Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS). An approximately (2±1) nm thin oxide film is produced at the surface of n-GaP(100) via oxidizing the surface at 0.8 V vs RHE (reversible hydrogen electrode) and subsequent hydrogen evolution at very cathodic potentials. The latter step is crucial for a substantial reduction of the potential for water splitting, presumably because the evolved hydrogen passivates electrically active defects in the oxide film. After appropriate surface conditioning, photolytic water splitting was observed without applied voltage or addition of catalysts, as confirmed by detection of hydrogen gas evolving at the Pt counter cathode with a gas spectrometer. The n-GaP(100) photoanode was exposed to high-intensity illumination (120 mW/cm 2 ) at 0 V vs RHE in 0.02 M HCl electrolyte for a duration of 3 days while yielding stable photocurrents. Ex-situ surface characterization of the n-GaP(100) photoanodes was carried out after extended PEC water splitting. AFM revealed a very flat surface, and no signs of corrosion were observed even after extended periods of water splitting. AES depth profiles showed that phosphorous was depleted near the surface of the n-GaP(100) photoanode. Using AES spectra, the thickness of the oxide film was estimated. XPS measurements revealed that the surface oxide consists mainly of Ga 2 O 3 , while small concentrations of GaPO 4 , P 2 O 5 and also metal-like Ga are also present at the topmost surface layers of the n-GaP(100) photoanode. Electrochemical impedance spectroscopy (EIS) was carried out to understand the charge transfer processes across the semiconductor/electrolyte interface. Our EIS results suggest that defect states in the surface oxide and metal-like Ga at the very surface in contact with the electrolyte play crucial roles in the effective charge transfer across the semiconductor-electrolyte interface. Our surface conditioning processes lead to the formation of a nonporous, thin and stable Ga surface oxide which inhibits PEC surface corrosion and, at the same time, subserves the water splitting process.

Probing the Surface Oxidation of III-V Photoelectrodes with First-Principles Simulations and in Situ Experiments

Integrating Ab-Initio Simulations and Experimental Characterization Methods for Understanding Chemistry at Complex Photoelectrochemical Interfaces

Kinetically Versus Thermodynamically Controlled Factors Governing Elementary Pathways of GaP(111) Surface Oxidation

Modulation of Surface Bonding Topology: Oxygen Bridges on OH- Terminated InP (001)

(Invited) (Photo-)Electrochemical Reactions on Semiconductor Surfaces:Si and III-V Surfaces – Atomic and Electronic Structure

(Invited) Understanding Photoelectrocatalysis on Epitaxial Oxide Surfaces

Integrating Ab Initio Simulations and X-ray Photoelectron Spectroscopy: Toward A Realistic Description of Oxidized Solid/Liquid Interfaces

Elucidating the Role of Surface Energetics on Charge Separation During Photoelectrochemical Water Splitting

Oxidation-Induced Polymerization of InP Surface and Implications for Optoelectronic Applications

Interface Engineering and Its Effect on WO3-Based Photoanode and Tandem Cell.

Tuning Surface Electronics State of P-Doped In2.77S4/In(OH)3 Toward Efficient Photoelectrochemical Water Oxidation.

Photolytic Water Splitting By Surface-Conditioned n-Gallium Phosphide(100) Photoanodes

On the origin of the photocurrent of electrochemically passivated p-InP(100) photoelectrodes.

Interfacial engineering of gallium indium phosphide photoelectrodes for hydrogen evolution with precious metal and non-precious metal based catalysts

Investigation on in situ sulfide/nitride/phosphide treatments of hematite photoanodes for improved solar water oxidation

Transition from Sequential to Concerted Proton-Coupled Electron Transfer of Water Oxidation on Semiconductor Photoanodes

Interfacial Engineering of In2O3/In2S3 Heterojunction Photoanodes for Photoelectrochemical Water Oxidation

Material Design and Surface/Interface Engineering of Photoelectrodes for Solar Water Splitting

Engineering Surface Architectures for Improved Durability in III-V Photocathodes

Evolution of Surface Oxidation on Ta3N5 As Probed by a Photoelectrochemical Method

Engineering the Interfacial Structure of Heavy Metal-Free Colloidal Heterostructured Quantum Dots for High-Efficiency Photoelectrochemical Water Oxidation without Co-Catalyst