Abstract:The enhancement of cryogenic plasticity for some aluminum alloys has attracted broad attention, which provides a new approach to the formability improvement of high-strength aluminum alloys. However, the hardening behavior and the ductility of aluminum alloys at cryogenic temperatures are very sensitive to the microstructure tempered at different conditions, with complex combination of GP zones, second phase precipitates, coarse and equilibrium phases. In this paper, three groups of tempered AA7075 aluminum alloy sheets are elaborately designed by means of different approaches, i.e., solution-treated (W), peak artificial aged (T6), and fast re-dissolved (FD) from T6, to investigate their cryogenic deformation behavior and failure mechanism. The effect on cryogenic plasticity of second phases, including the coarse particles in the matrix and the precipitate free zones (PFZs) accompanied by chain distributed particles along grain boundary, can be isolated by comparison among these three kinds of AA7075 alloys. The cryogenic mechanical properties of AA7075 sheets are evaluated by uniaxial tensile test, and the microstructure evolution observed by transmission electron microscope (TEM), scanning electron microscope (SEM) and laser confocal microscope (LCM). It shows that the enhancement of both ductility and continuous work hardening for W- and FD-tempered AA7075 sheets at cryogenic temperatures results from the uniformly distributed dislocations in the matrix of supersaturated solid solution (SSSS). The relatively low cryogenic ductility of AA7075-FD in comparison with AA7075-W results from the cracked η phases in the interior of grain, which has an increasing brittleness and high stresses on the particle due to the bypassing process at cryogenic condition. Furthermore, the undesirable early fracture of AA7075-T6 alloy during cryogenic deformation process is systematically illustrated from the aspect of interaction between dislocation and second-phase particles. Beside the cracked η phases in the interior of grains, defects also appear in the non-coherent interface between PFZ and the equilibrium η phase due to stain localization at grain boundary. As a result, AA7075-T6 alloy exhibits a ductile-brittle mixed fracture mode dominated by PFZ and the equilibrium η phase at grain boundary.

Damage and fracture prediction of 7075 high-strength aluminum alloy during cryogenic stamping process

Damage and failure characterization of 7075 aluminum alloy hot stamping

Cryogenic Deformation Behavior and Failure Mechanism of AA7075 Alloy Sheets Tempered at Different Conditions

The improvement of deformability in AA7075 alloy through cryogenic treatment and its correlation with microstructural evolution and FE modelling

Fracture behavior of 7075-T6 aluminum alloy under electromagnetic forming and traditional stamping

Tensile properties and a modified s-Johnson-Cook model for constitutive relationship of AA7075 sheets at cryogenic temperatures

Hot tensile deformation behavior and microstructure evolution of 7075 aluminum alloy sheet

Fatigue and fracture behavior of an aluminum-lithium alloy 8090-T6 at ambient and cryogenic temperature

Mechanical properties and microscopic mechanisms of 2219-T6 aluminum alloy under dynamic tension with cryogenic temperatures

Global Damage Behavior and Formability Prediction of AA2219 FSW Blanks at Cryogenic Temperature

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature

Cryogenic Deformation Behaviour of Aluminium Alloy 6061-T6

Neural network-based ductile fracture model for 5182-O aluminum alloy considering electroplastic effect in electrically-assisted processing

Effects of Deformation at High, Medium, and Cryogenic Temperatures on the Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys

Modeling of constitutive behavior and ductile fracture of AA5A06 aluminum alloy sheet in warm hydroforming process

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

Ductile Fracture and S–N Curve Simulation of a 7075-T6 Aluminum Alloy under Static and Constant Low-Cycle Fatigue

Cryogenic Formability of a Solution-Treated Aluminum Alloy Sheet at Low Temperatures

Study on High-Temperature Mechanical Properties and Forming Limit Diagram of 7075 Aluminum Alloy Sheet in Hot Stamping

Research on constitutive model of aluminum alloy 7075 thermal deformation based on deep neural network

Prediction of Strain Path Changing Effect on Forming Limits of AA 6111-T4 Based on a Shear Ductile Fracture Criterion