Abstract:The enhancement of cryogenic plasticity for some aluminum alloys has attracted broad attention, which provides a new approach to the formability improvement of high-strength aluminum alloys. However, the hardening behavior and the ductility of aluminum alloys at cryogenic temperatures are very sensitive to the microstructure tempered at different conditions, with complex combination of GP zones, second phase precipitates, coarse and equilibrium phases. In this paper, three groups of tempered AA7075 aluminum alloy sheets are elaborately designed by means of different approaches, i.e., solution-treated (W), peak artificial aged (T6), and fast re-dissolved (FD) from T6, to investigate their cryogenic deformation behavior and failure mechanism. The effect on cryogenic plasticity of second phases, including the coarse particles in the matrix and the precipitate free zones (PFZs) accompanied by chain distributed particles along grain boundary, can be isolated by comparison among these three kinds of AA7075 alloys. The cryogenic mechanical properties of AA7075 sheets are evaluated by uniaxial tensile test, and the microstructure evolution observed by transmission electron microscope (TEM), scanning electron microscope (SEM) and laser confocal microscope (LCM). It shows that the enhancement of both ductility and continuous work hardening for W- and FD-tempered AA7075 sheets at cryogenic temperatures results from the uniformly distributed dislocations in the matrix of supersaturated solid solution (SSSS). The relatively low cryogenic ductility of AA7075-FD in comparison with AA7075-W results from the cracked η phases in the interior of grain, which has an increasing brittleness and high stresses on the particle due to the bypassing process at cryogenic condition. Furthermore, the undesirable early fracture of AA7075-T6 alloy during cryogenic deformation process is systematically illustrated from the aspect of interaction between dislocation and second-phase particles. Beside the cracked η phases in the interior of grains, defects also appear in the non-coherent interface between PFZ and the equilibrium η phase due to stain localization at grain boundary. As a result, AA7075-T6 alloy exhibits a ductile-brittle mixed fracture mode dominated by PFZ and the equilibrium η phase at grain boundary.

Cryogenic Formability of a Solution-Treated Aluminum Alloy Sheet at Low Temperatures

A Novel Deep Drawing Process for Aluminum Alloy Sheets at Cryogenic Temperatures

Enhanced deep drawing formability and deformation mechanism of aluminum alloy at cryogenic temperature

Analyses on Formability and Flow Stress of an Al-Cu-Mn Alloy Sheet under Biaxial Stress at Cryogenic Temperatures

Investigation on the formability and deformation mechanism of aluminum alloy thin-walled parts at cryogenic temperature

Deformation behavior of Al–Cu–Mn alloy sheets under biaxial stress at cryogenic temperatures

Cooperative Enhancements in Ductility and Strain Hardening of a Solution-Treated Al–Cu–Mn Alloy at Cryogenic Temperatures

Mechanism of considerable strain hardening in ultrafine-grained pure aluminum sheets at cryogenic temperatures

Comparative study on the formability and microstructure evolution of different tempered Al–Cu–Li alloy sheets during room and cryogenic temperature forming process

Mechanical properties and microscopic mechanisms of 2219-T6 aluminum alloy under dynamic tension with cryogenic temperatures

Cryogenic Deformation Behavior and Failure Mechanism of AA7075 Alloy Sheets Tempered at Different Conditions

Prediction for cryogenic formability of AA2219 alloy cylindrical parts with friction stir weld

Cryogenic Deformation Behaviour of Aluminium Alloy 6061-T6

Workability Improvement on Al Alloy Inhomogeneous Blanks by Cryogenic Forming

Effects of Deformation at High, Medium, and Cryogenic Temperatures on the Microstructures and Mechanical Properties of Al-Zn-Mg-Cu Alloys

Deformation Behavior of Pure Aluminum at Room and Cryogenic Temperatures

Predicting Sheet Forming Limit of Aluminum Alloys for Cold and Warm Forming by Developing a Ductile Failure Criterion

Fatigue and fracture behavior of an aluminum-lithium alloy 8090-T6 at ambient and cryogenic temperature

Revealing the Exceptional Cryogenic Strength-Ductility Synergy of a Solid Solution 6063 Alloy by In-Situ EBSD Experiments

Cooperative Effect of Grain Size and Cryogenic Temperature on Deformation Behavior and Mechanism of Commercial Pure Al Sheets

Analysis on exceptional cryogenic mechanical properties of AA2219 alloy FSW joints in multi-scale