Abstract:The abundance of low-temperature waste heat produced by industry and automobile exhaust necessitates the development of power generation with thermoelectric (TE) materials. Commercially available bismuth telluride-based alloys are generally used near room temperature. Materials that are composed of p-type bismuth telluride, which are suitable for low-temperature power generation (near 380 K), were successfully obtained through Sb-alloying, which suppresses detrimental intrinsic conduction at elevated temperatures by increasing hole concentrations and material band gaps. Furthermore, hot deformation (HD)-induced multi-scale microstructures were successfully realized in the high-performance p-type TE materials. Enhanced textures and donor-like effects all contributed to improved electrical transport properties. Multiple phonon scattering centers, including local nanostructures induced by dynamic recrystallization and high-density lattice defects, significantly reduced the lattice thermal conductivity. These combined effects resulted in observable improvement of ZT over the entire temperature range, with all TE parameters measured along the in-plane direction. The maximum ZT of 1.3 for the hot-deformed Bi0.3Sb1.7Te3 alloy was reached at 380 K, whereas the average ZTav of 1.18 was found in the range of 300–480 K, indicating potential for application in low-temperature TE power generation. Thermoelectric materials, which convert temperature differences and electric voltage into each other, serve in refrigeration or power generation applications. Currently, bismuth telluride (Bi2Te3) and its alloys are the most widely used thermoelectric materials. Tie-Jun Zhu, Xin-Bing Zhao and co-workers from Zhejiang University, China, have now investigated the effect of antimony (Sb) alloying on bismuth tellurides through a series of polycrystalline solid solutions of Bi2-xSbxTe3—where x varies between 1.4 and 1.8—prepared by hot deformation. Systematic tuning of the alloy composition showed that higher antimony content raised the material's optimal conversion temperature by repressing undesirable conduction. This effect arises from an increase in both the hole concentration and the band gap in the material. For a composition where x is 1.7, the alloy showed optimal performances at 380 kelvin—a suitable temperature for low-temperature power generation from the waste heat generated by industry or vehicles. The p-type bismuth telluride-based polycrystalline materials suiting for low-temperature power generations (near 380 K) have been obtained through Sb-alloying and HD, which suppresses the detrimental effect of intrinsic conduction at elevated temperature via increasing the hole concentration and band gap. The hot-deformed Bi0.3Sb1.7Te3 alloy, not usual composition Bi0.5Sb1.5Te3, shows a maximum ZT of 1.3 at 380 K, indicating a bright application potential in low-temperature power generations.

Organic/Inorganic Hybrid Design as a Route for Promoting the Bi<sub>0.5</sub>Sb<sub>1.5</sub>Te<sub>3</sub> for High-Performance Thermoelectric Power Generation

High Performance Thermoelectric Power of Bi 0.5 Sb 1.5 Te 3 Through Synergistic Cu 2 GeSe 3 and Se Incorporations

Enhanced Thermoelectric Performance of P‐Type (Bi,Sb)2Te3 by Incorporating Non‐Stoichiometric Ag5Te3 and Refining Te‐Se Ratio

High‐Efficiency Thermoelectric Power Generation Enabled by Homogeneous Incorporation of MXene in (Bi,Sb)2Te3 Matrix

Enhanced Thermoelectric Properties of Bi2Te2.7Se0.3/hexagonal BN Composites and Optimized Modules for Power Generation

All-Inorganic Halide Perovskites Boost High-Ranged Figure-of-Merit in Bi0.4Sb1.6Te3 for Thermoelectric Cooling and Low-Grade Heat Recovery

Optimized Thermoelectric Properties of Bi0.48Sb1.52Te3 Through AgCuTe Doping for Low-Grade Heat Harvesting.

All-Inorganic Halide Perovskites Boost High-Ranged Figure-of-Merit in Bi 0.4 Sb 1.6 Te 3 for Thermoelectric Cooling and Low-Grade Heat Recovery

High‐Performance Industrial‐Grade p‐Type (Bi,Sb)2Te3 Thermoelectric Enabled by a Stepwise Optimization Strategy

Achieving High Thermoelectric Performance in p-Type BST/PbSe Nanocomposites through the Scattering Engineering Strategy

Organic/Inorganic Hybrid Design as a Route for Promoting the Bi 0.5 Sb 1.5 Te 3 for High‐Performance Thermoelectric Power Generation

High‐Efficiency Thermoelectric Module Based on High‐Performance Bi0.42Sb1.58Te3 Materials

High Performance Dual-mode Module for Power Generation and Cooling Based on Optimized BiSbTe

High density lath twins lead to high thermoelectric conversion efficiency in Bi2Te3 modules

Critical Role of Tellurium Self-Compensation in Enhancing the Thermoelectric Performance of P-Type Bi0.4Sb1.6Te3 Alloy

Exceptional Thermoelectric and Mechanical Performance in (bi, Sb)2Te3 Matrix Facilitated by AgInSe2 Alloying

BiSbTe alloy with high thermoelectric and mechanical performance for power generation

Shifting Up the Optimum Figure of Merit of P-Type Bismuth Telluride-Based Thermoelectric Materials for Power Generation by Suppressing Intrinsic Conduction

Vacancy Manipulation by Ordered Mesoporous Induced Optimal Carrier Concentration and Low Lattice Thermal Conductivity in BixSb2- xTe3 Yielding Superior Thermoelectric Performance

High Performance BiSbTe Alloy for Superior Thermoelectric Cooling

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi0.48Sb1.52Te3-AgSbSe2 Composite.